lathes used for sale (3,142)

control: FANUC 21i-TB Control x-axis: 390 mmz-axis: 780 mmspindle taper: A2-11 number of spindle speeds: 2000rpm engine output: 37 kWweight of the machine ca.: 9000 kgdimensions of the machine ca.: 1905,0 × 2720,0 × 3260,0 mThe machine has chucks that can produce gears from 100 to 500 mm.Special chuck is availableThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

greates pass round over bed: 820 mmworkpiece weight max.: 2.000 kgturning speeds: 7,1 - 1.400 U/minLongitudinal Feed: 0,063 - 56 mmPlanar Feed: 0,05 - 28 mmTravel Distance Plan Slider: 520 mmTravel distance of the tailstock quill: 280 mmcenter height over square guideway: 400 mmbed width: 560 mmfaceplate diameter: 800 mmtotal power requirement: 30 kWMain Spindle: - Spindle head (DIN 55022): 11 - Camlock spindle head: 11 - Spindle bore diameter: 128 mm - Spindle diameter at the front bearing: 170 mmLead screw: - Pitch: 12 mm - Diameter: 54 mmCircumferential diameter over the long cross slide: 515 mmCircumferential diameter in the bed recess: 890 mmLength of the  ...

: 0400 mm: 246 mm: 1250 mm: 195 mm: 54 mm: 7,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0460 mm: 270 mm: 1500 mm: 230 mm: 76 mm: 11 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

center height over bed: 500 mmcentre distance: 6.000 mmbed width: 670 mmturning diameter over bed: 1.030 mmturning dia. over face-slide: 640 mmMax. workpiece weight between centers: 5.000 kgMax. workpiece weight between centers (collet): 6.000 kgfeed speeds x- and z-axis: 6.500 mm/minspindle head: ASA 15 spindle turning speed range: 4 - 830 U/minTorque: 6.224 Nmtotal power requirement: 70 kWweight of the machine ca.: 11,3 tHeadstock: - Front bearing, inside diameter: 235 mm - Rear bearing, inside diameter: 216 mm - Diameter of hole through spindle: 170 mm - Morse taper in spindle sleeve: 6 MKTailstock: - Quill diameter: 150 mm - Quill travel: 400 mm - Quill morse taper: 6 MKSaddle and cross slide: ...

turning diameter: 200 mmturning length: 1000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Technical data Lead and pull spindle lathe Manufacturer: NARDINI Type: ND 220 AE Speed range: 25 - 2000 rpm Electrical connection: 380 V / 50 Hz Connected load: 6.3 kW 3-jaw chuck Ø approx. 250 mm Configuration With guide and pull spindle With tailstock With quick-change steel holder Tapping device available Feed and thread tables on the machine Integrated machine substructure Emergency stop switch available Machine with splash guard Auction-ID: A7-49302-3016

Technical data Manufacturer: Maschinen Wagner Type: WDE 500 Machine Type: Cycles CNC Flatbed Lathe (Source: Online Research) Year of Make: 2014 Control: Siemens SINUMERIK 828D BASIC T Operating voltage: 400 V / 50 Hz Rated current: 40 A Connected load: 24 kVA Weight: 3.0 t Max. circumferential diameter over bed: 500 mm (Source: online research) Max. turning diameter over cross slide: 280 mm (Source: Online research) Max. centre width: 1,500 mm (Source: Online research) Spindle bore: 82 mm (Source: Online research) Spindle speed ranges: 7–135 / 30–550 / 110–2,200 rpm (Source: Online research) Spindle motor: 7.5 kW (Source: online research) Travel X/Z: 295 / 1,435 mm (Source: Online research) Configuration Machine housing with sliding doors, movable control panel, tailstock, quick-change steel holder, machine lighting and coolant supply. Visible accessory with three-jaw chuck and se ...

Technical data Manufacturer: K. Martin Maschinenfabrik, Offenburg Type / Model: KM 40 Design: conventional lathe Spindle speeds: 31.5 / 45 / 63 / 90 / 125 / 180 / 250 / 355 / 500 / 710 / 1,000 / 1,400 rpm Configuration 3-jaw chuck Tailstock Tool Holder Operating instructions for KM 40 lathe available Remarks The machine comes from a well-maintained company liquidation and was actively used in ongoing production until the end. Auction-ID: A7-49302-183

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 79430 €: 1501.23 €: 600 mm: 1500 mm: 300 mm: 80 mm: 400 mm: 400 mm: 8 : 90 MK: 3 : 20 - 100, 80 - 400, 400 - U/Min: max. 8 m/min: max. 8 m/min: 290 mm: 90 mm: 5 MK: 225 mm: 11 kW: 3,5 / 22 kW/Nm: 1,75 / 11 kW/Nm: 120 Nm: 1250 daN: 1050 daNFast and simple communication between the operator and the lathe.Simple workpieces are machined in the same way as on the universal lathe, but more efficient.Complicated workpieces are machined in the same way as on the universal lathe, but faster.Complicated workpieces are machined in the same way as on the CNC lathe, but easier.Based on the controller Schneider Magelis the intelligent, self-developed ZMM Sliven softwareleads the operator also without programming skills simple and fast to the finished workpiece.The interface is simple and with large icons, which is convenient in a specific work enviro ...

: neu : Bulgarien : 114970 €: 2172.93 €: 890 mm: 3000 mm: 400 mm: 155 mm: 490 mm: 700 mm: 15 : 160 MK: 24 : 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 22 kW: 7500 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 100120,00 turning length2.000 mm € 103850,00 turning length4.000 mm € 123510,00 turning length5.000 mm € 134810,00 turning length6.000 ...

: neu : Bulgarien : 81780 €: 1545.64 €: 760 mm: 3000 mm: 380 mm: 132 mm: 520 mm: 560 mm: 11 : 140 MK: 17 : 7,5 - 1015 1/min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4470 kgdriven by conventional transmission3-axes digital readoutquick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centerfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 67770,00 turning ...

: gebraucht : 2015 : 1686 : prompt, Zwischenverkauf v : England : 14800 €: 1 : 330 mm: 1000 mm: 167 mm: 38 mm: 210 mm: 12 : 40 - 2500 1/min: 16 : 0.03 - 1 mm/U: 0.2 - 14 mm: 2 - 56 TPI Gänge/: 190 mm: 92 mm: 42 mm: 3 MK: 110 mm: 2.2 kW: 1940 mm: 1000 mm: 1550 mm: 685 kg3-axis digital read out Newall4-jaw chuck Bison diameter 160mm with inside and outside jawsQuick-change tool post with 1 holdCoolant deviceChuck protectionSteel holder protectionLead screw coverMachine lightManual brakeOperating manual in German with EC declaration of conformityBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demonstration via video call• R ...

: neu : ca. 6 Monate ab Auftragse : Taiwan : 87350 €: 1650.92 €: 540 mm: 1500 mm: 85 mm: 310 mm: 350 mm: D1-8 : 1/20 MK: 3 : 27 - 2250 1/min: 5000 mm/min: 8000 mm/min: 280 mm: 75 mm: 5 MK: 190 mm: 9 / 13,5 (S1 / S6 40%) kW: 0.02 mm: 0.016 mm: ISO3655 : 3340 mm: 1905 mm: 2235 mm: 3400 kgTHREE OPERATING MODES: CNC / TEACH-IN / MANUALSiemens 828D CNC control• 12-inch colour screen• Linear interpolation• Circular interpolation• Helical interpolation• Skip function• Workpiece coordinate system• Coordinate system rotation• Rigid tapping• Mirror image, scaling and rotation• Turning cycle• ShopTurn softwareLarge spindle bore, with precision bearings for high accuracy and consistent cutting stability.Precision ball screw Ø 40 mm (Class C5) on the Z-axis and ball screw Ø 25 mm (Class C3) on the X-axis.2-axis AC servo motors50-300 mm roller-type tailstock.Manual tailstoc ...

: gebraucht : 2023 : 1675 : prompt, Zwischenverkauf v : Bulgarien : 17600 €: 1 : 325 mm: 1000 mm: 165 mm: 32 mm: 190 mm: 200 mm: 5 : 4,5 MK: 12 : 85 - 2.000 1/min: 48 : 0.006 - 1.77 mm/U: 0.003 - 0.885 mm/U: 0.1 - 28 mm: 75 - 2,5 Gänge/: 0.1 - 1.75 : 150 mm: 95 mm: 40 mm: 3 MK: 100 mm: 2.2 kW: 2150 mm: 950 mm: 1350 mm: 770 kgdemo machine / mint conditionnet price (price for new machine € 23.970,00)driven by manual transmission3-axes digital readout Fagor 40iquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 160 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",incl. following optional equipment:1 lenght stopBUYING USED MACHINER ...

: neu : Bulgarien : 58370 €: 1103.19 €: 600 mm: 2000 mm: 300 mm: 80 mm: 400 mm: 400 mm: 8 : 90 MK: 3 : 20 - 100, 80 - 400, 400 - U/Min: 120 : 64 : 0.5 - 120 mm: 60 - 1/4 Gänge/: 0.125 - 30 : 315 mm: 130 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3600 mm: 1500 mm: 1650 mm: 3110 kgIn contrast to the universal lathes, here the adjustment of the revolutions is infinitely variable by means of a frequency inverter.It is possible to ensure a ",constant cutting speed", (V-const), i.e. when changing the diameter to be machined, the speed remains unchanged and thus a higher accuracy and smoothness of the surface is achieved. At the customer&apos,s request, the machines can be manufactured with a reading of the linear displacement and positioning by mounting a digital display.driven by variable speed control (3 steps)3-axes digital readout Fagor with CSS (constant surface speed)quick change toolp ...

: neu : Bulgarien : 140320 €: 2652.05 €: 1320 mm: 3000 mm: 625 mm: 155 mm: 940 mm: 700 mm: 15 : 160 MK: 4 : 3,7 - 15,6, 14,7 - 62, 58 U/Min: 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 1/16 - 60 Gänge/: 0.125 - 120 : 685 mm: 270 mm: 125 mm: 6 MK: 260 mm: 30 kW: 8550 kgdriven by variable speed control (4 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 125460,00 turning length4.000 mm € 148950,00 turning ...

: neu : Bulgarien : 121770 €: 2301.45 €: 1090 mm: 3000 mm: 500 mm: 155 mm: 690 mm: 700 mm: 15 : 160 MK: 24 : 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 22 kW: 7500 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS turning length1.500 mm € 107020,00 turning length2.000 mm € 110650,00 turning length4.000 mm € 130410,00 turning length5.000 mm € 141610,00 turning length6.000 ...

: neu : Bulgarien : 96240 €: 1818.94 €: 860 mm: 3000 mm: 430 mm: 135 mm: 620 mm: 560 mm: 11 : 140 MK: 7 - 42, 28 - 170, 165 - 1 U/Min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 240 : 435 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4650 kgdriven by variable speed control (3 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centermain motor with frequency invertorfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachin ...

: neu : Bulgarien : 89440 €: 1690.42 €: 760 mm: 3000 mm: 380 mm: 132 mm: 520 mm: 560 mm: 11 : 140 MK: 3 : 7 - 42, 28 - 170, 165 - 1 U/Min: 150 : 0.039 - 18 mm/U: 0.02 - 9 mm/U: 0.5 - 180 mm: 60 - 1/6 Gänge/: 0.125 - 45 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 15 kW: 4470 kgdriven by variable speed control (3 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round)3-jaw chuck Bison3295/DIN6350, Ø 400 mmspindle dead centermain motor with frequency invertorfour way rapid traverse devicefoot pedal brakelongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocktailstock quill reducermechanized movement of tailstocklow voltage machine lampoperating manualmachine  ...

: neu : Bulgarien : 56920 €: 1075.79 €: 630 mm: 2000 mm: 315 mm: 103 mm: 430 mm: 400 mm: 11 : 120 MK: 21 : 12,5 - 1250 1/min: 120 : 0.04 - 12 mm/U: 0.02 - 6 mm/U: 0.5 - 120 mm: 60 - 1/4 Gänge/: 0.125 - 30 : 240 - 1 : 315 mm: 90 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3310 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 315 mmspindle dead centerlongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.000 mm € 53520,00 turning length1.500 mm € 54880,00 turning length3.000 mm € 61360,00 turning length4.000 mm € 67270,00 turning len ...

: neu : ca. 6 Monate ab Auftragse : Taiwan : 77850 €: 1471.37 €: 460 mm: 1000 mm: 56 mm: 230 mm: 350 mm: D1-6 : 1/20 MK: 3 : 33 - 3100 1/min: 5000 mm/min: 8000 mm/min: 280 mm: 75 mm: 5 MK: 190 mm: 9 / 13,5 (S1 / S6-40%) kW: 0.02 mm: 0.01 mm: ISO3655 : 2840 mm: 1905 mm: 2235 mm: 2900 kgTHREE OPERATING MODES: CNC / TEACH-IN / MANUALSiemens 828D CNC control• 12-inch colour screen• Linear interpolation• Circular interpolation• Helical interpolation• Skip function• Workpiece coordinate system• Coordinate system rotation• Rigid tapping• Mirror image, scaling and rotation• Turning cycle• ShopTurn softwareWith precision bearings ensuring spindle runout of less than 0.005 mm,for high accuracy and consistent cutting stability.Precision ball screw Ø 40 mm (class C5) on the Z-axis and ball screw Ø 25 mm (class C3) on the X-axis.2-axis AC servo motors20-160 mm roller-type  ...

: neu : Bulgarien : 64180 €: 1213 €: 630 mm: 2000 mm: 315 mm: 103 mm: 430 mm: 400 mm: 11 : 120 MK: 3 : 16 - 63, 63 - 250, 315 - U/Min: 120 : 0.04 - 12 mm/U: 0.02 - 6 mm/U: 0.5 - 120 mm: 060 - 1/4 Gänge/: 0.125 - 30 : 315 mm: 130 mm: 90 mm: 5 MK: 230 mm: 11 kW: 3310 kgdriven by variable speed control (2 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 315 mmspindle dead centerlongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length 1.000 mm € 60780,00 turning length1.500 mm € 62160,00 turning length3.000 mm €  ...

: neu : Bulgarien : 126650 €: 2393.69 €: 890 mm: 3000 mm: 400 mm: 155 mm: 490 mm: 700 mm: 15 : 160 MK: 4 : 3,7 - 15,6, 14,7 - 62, 58 U/Min: 160 : 0.032 - 38.9 mm/U: 0.016 - 19.45 mm/U: 0.5 - 480 mm: 60 - 1/16 Gänge/: 0.125 - 120 : 525 mm: 270 mm: 125 mm: 6 MK: 260 mm: 30 kW: 7500 kgdriven by variable speed control (4 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 500 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platestailstock quill reducerelectric motor movement of tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.500 mm € 111610,00 turning length2.000 mm € 115430,00 turning  ...

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 113720 €: 2149.31 €: 800 mm: 2000 mm: 400 mm: 315 mm: 560 mm: 560 mm: 318 MK: 12 : 8 - 400 1/min: 152 : 0.039 - 15 mm/U: 0.02 - 7.5 mm/U: 76 : 0.5 - 150 mm: 60 - 1/5 Gänge/: 0.125 - 37.5 : 240 - 4/5 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 11 kW: 6100 kgTheir main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry.Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters.The clamping of the pipes with two universals and stands allows the processing of long pipes.These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities.Drive via gearboxElectrodynamic brake3-axis digital display FagorQuick-change tool holder Amestra type C, system like Multifix i ...

turning length: 850 mmturning diameter: 400 mmswing diameter over bed slide: 245 mmspindle bore: 52.0 mmturning speeds: 45 - 1800 U/minbed width: 260 mmspindle taper: DIN 55029 D 1-5taper in tailstock: 3 MKquill travel: 120 mmtotal power requirement: 3.0 / 4.5 kWweight of the machine ca.: 1255 kgrange L-W-H: 1900 x 1000 x 1610 mmEquipment:- 3-axis digital display ES-12 V with LCD display- 3-jaw chuck PS3-200 mm / D5- Clamping disk 320 mm- Fixed steady rest - passage diameter max. 130 mm- Follow-on steady rest - passage diameter max. 100 mm- Coolant system- Quick-change tool holder with 4 inserts- Protective device for quick-change tool holder- Micrometer longitudinal stop- Slip clutch- Motor with magnetic brake in accordance with CE standard- Initial filling with Shell Tellus 46- Extendable chip tray- LED machine light- Change gears- Reduction sleeve- 2 centering points- Chip rear wall-  ...

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 138800 €: 2623.32 €: 1020 mm: 2000 mm: 510 mm: 358 mm: 770 mm: 560 mm: 361 MK: 12 : 6,3 - 315 1/min: 152 : 0.039 - 15 mm/U: 0.02 - 7.5 mm/U: 76 : 0.5 - 150 mm: 60 - 1/5 Gänge/: 0.125 - 37.5 : 240 - 4/5 : 505 mm: 270 mm: 105 mm: 6 MK: 225 mm: 18.5 kW: 6400 kgTheir main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry.Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters.The clamping of the pipes with two universals and stands allows the processing of long pipes.These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities.Drive via gearboxElectrodynamic brake3-axis digital display FagorQuick-change tool holder Amestra type D1, system like Mult ...

turning diameter: 40 mmturning length: 50 mmcontrol: Fanuc 0i-TD Spindle Speed: 8000 U/min.travel -x axis: 180 mmtravel -z axis: 200 mmrapid power traverse in X-and Z direction: 15 m/minweight of the machine ca.: 1500 kgdimensions of the machine ca.: 1500x700x1600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 750 mmturning diameter: 310 mmturning diameter over slide rest: 175 mmspindle bore: 32.0 mmtailstock quill taper MT: 3 MKturning speeds: 85 - 2200 U/minbed width: 200 mmspindle taper: DIN 55027 GR 5 total power requirement: 2.2 kWweight of the machine ca.: 710 kgrange L-W-H: 1884 x 717 x 1262 mm New price ~ 20.000 euros from a technical college ()- in checked condition - machine videos -https://www.youtube.com/watch?v=iqU7Bkh6INohttps://www.youtube.com/wa tch?v=aSViqjk51IkFurnishing:- Robust conventional center lathe- 3-jaw lathe chuck Ø 160 mm, with replacement jaws- NEWALL digital display, front left- MULTIFIX steel holder with 4x inserts- fixed bezel- moving bezel- Movable tailstock- Foot/spindle brake- Machine swing feet- User manual (PDF/NL) all technical data:- Turning diameter over bed 310 mm- Distance between centers 750 mm- Turning diameter over support 175 mm-  ...

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 113620 €: 2147.42 €: 800 mm: 2000 mm: 400 mm: 260 mm: 560 mm: 560 mm: 318 MK: 12 : 8 - 400 1/min: 152 : 0.039 - 15 mm/U: 0.02 - 7.5 mm/U: 76 : 0.5 - 150 mm: 60 - 1/5 Gänge/: 0.125 - 37.5 : 240 - 4/5 : 410 mm: 150 mm: 105 mm: 6 MK: 225 mm: 11 kW: 6000 kgTheir main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry.Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters.The clamping of the pipes with two universals and stands allows the processing of long pipes.These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities.Drive via gearboxElectrodynamic brake3-axis digital display FagorQuick-change tool holder Amestra type C, system like Multifix i ...