thermoforming machines used for sale (73)

carrying capacity: 900 kgweight of the machine ca.: 119 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

-PRODUCTION OF CUPS & MUGS OF EVERY SHAPE Machine consists of: -1x Roll-off block -Preheater 4 Play (Age: 2007) -Thermoformer Gabler M92L -Pick-up stacker (packaging unit)

(LIDS PRODUCTION) Machine consists of: -1x Roll-off block -Thermoformer Gabler Swing -Stacking

1.0 pcs. Vertical press for use: SMC (Sheet Molding Compound) Manufacturer: LAUFFER Type: PRKP120 Year of Make: 1972 Pressing force: 120 tons Table; 1,200 x 1,000 mm Additional heated Table surface: 800 x 800 mm Installation height: 810 mm Stroke: 790 mm Opening: 1,600 mm

M. No.: 322 Max. film width 700-800 mm Equipment / Additional information: -GREINER STACKING / Transfer device R3 (Ref. No.: 95002.24) // M. No.: 00020 // Age: 1998 Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp The following tools were used on the machine: 8-way WZ-Ø95 and 15-way WZ-Ø73 and 15-way WZ-Ø86 Packaging was produced especially for the dairy industry. The cycles are 18-25 strokes - depending on the cup weight.

Technical specifications: Rated power, kW: 11,3 Mold area, mm: 475 x 250 Max. film width, mm: 495 Min. film width, mm: 150 Max. feed length, mm: 280 Min. feed length, mm: 50 Max. drawing depth/negative, mm: 100 Number of cycles/min.-max.: 48 Consumption of air/cycle at 6 bar: 100 Nl (net-pressurized air) Heat energy to be dissipated: with top heating ca. 10 260 KJ/h with top and bottom heating ca.: 17 715 KJ/h Special equipment: Hollow floor facility available Control cabinet: included

THERMO FORMING MACHINE TFT IMC 5030 (WITH TOOLS) M. No.: 403 Equipment / Additional information: unwinding: Roll recording: easy Max roll diameter: mm 1000 Settlement: automatically Thermoforming machine: Maximum tool dimensions: mm 520x330 Pos. Molding height max .: 15 mm Neg. Molding height max .: 120 mm Sheet width: mm 150/760 Movement Step: mm 50/330 Max HIPS film thickness: 1.8 mm Hub of the sub-table: 150 mm Clamping force: 7500 Kg Inst power top heater: 18.8 Kw Inst power under heater: 14.1 Kw Idle clock speed: per minute 40th power main drive motor: 2.2 Kw Engine power. Film feed: 0.75 Kw Air operating pressure: Kg / cm2 7 Water consumption at 12 °: 1t / 1` approx.30 Air consump. at 7 kg / cm2: 1t / cycle 125 Installed power: Kw 50 9xTool: Article no. // Tool no. // Cavities // Description / Product: 3599 // 457 // 10 // Ven ...

M. No.: 3284 Equipment / Additional information: (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe ...

WEYHMÜLLER CBU-ISO 10332 automatic COMBIPACK Machine for the application of Pre-Printed Blanks onto Round Cup/ Rectangular Container Walls,, Age 2017 only used for ca. 8000 hrs., The Combipack Thin-Walled Cup/ Containers (Products) use up to 60% less material than conventional thermoformed Products, the applied paper Blanks provide stability & strength. The Paper Blanks can be easily separated for recycling purposes., Machine Consisting of:-, • Elevator Tray Feeder, • Cup/ Container In-Feed Conveyor, • Universal 4 x Screw Denester, • Indexing Turret with 8 x Mandrels, • Turret Indexes to:, Cup/ Container infeed Station, Blank Feeder Station, Glue application Station, Blank Forming/ Folding Station, Glue Drying Station, Cup/ Container Bottom Labelling Position, Counter/ Stacker Station, • Pre-printed Blanks horizontal accumulator In-Feed Conveyor to:, • Vertically stacked B ...

Mould & Matic PET Round Lid Mold, to fit Ø95mm dia. Cups, 10-Cavity, age Dec. 2009, with Stacker Parts. Manufactured for the Gabler D600

ILLIG RDM70K Mold, dia. Ø70 mm, for PP Cups, 21 Cavities, age 1995, with 1 set of inserts and Stacker basket with Rods with Brushes.

ILLIG RDM70K Mold for Ø75 mm dia. PS Cups, 21-Cavities, with 1 set of inserts, no Stacking Basket, age 1995. missing engraved Cup bottom discs, as these are the intellectual property of the previous owner. Very sparingly used !

PET Coextrusion + Inline ILLIG RDKP72g Thermoforming Line, Age 2010, this equipment is suitable for PET, PP & PS Trays, Fruit & Vegetable baskets etc. :-, Inline S Plastic SRL PET Coextrusion line to produce pet sheet in-line with ILLIG RDKP72g 4-Station Thermoformer (.samplastco. hole punch station) Age 2010 :, Maximum output 680 kg/ hr, Maximum sheet width 800 mm, The line includes:, Electrical Control Panel, MSM Plastic Engineering Gravimetric Feeder, fed directly from the PET Dryer + additional Component for masterbatch or additive, Main extruder Model ED 100-40 dia. Ø100 mm, L/D 40, BP Plast BDO X2 100 Double plate hydraulic screen changer, MAAG Gear pump, Co-extruder Model E60-40 dia. Ø60 mm, L/D 40 with Gravimetric feeder, BP Plast Single plate hydraulic screen changer, MAAG Gear pump, 3- Layer (ABA) Melt Feed Adapter, Special extrusion die for PET, width 900 mm, 3-Roll Polished ...

Lid Mold Manufactured by TERMOSTAMPI to fit Drinking Cups Ø98 mm, Age 2022, Forming mold 24 cavities (6 x 4 arrangement), 2 sets of inserts for:, Dome Lid For Cup Ø9 8mm ., Flat Lid For Cup Ø 98mm, Hole Punch Mold - Punch and Die., 24 cavities to Punch 24 holes diam.25 mm on Dome Lid., 24 cavities to Punch 24 cross cut., Steel Rule Pucning Mold :, with 24 cavities for both Dome and Flat Lid., Stacking Device:, for Domes and Flat Lids

PP-Drinking Cup Mold for ILLIG RDM75Kc, manufactured by TERMOSTAMPI, age 2022 with Inmold Forming and Trimmimg, for PP-Cups Ø98 mm dia. for the ILLIG RDM 75Kc, consists of:, 24 cavities (6 x 4 arrangement), complete with Trimming Knives, Cavity Inserts, Ejectors, Down Holders., and 4 series of inserts for the following PP drinking cups:-, 24 oz, 20 oz, 16 oz, 12/ 14 oz, Complete with Stacker Parts for the ILLIG PH75 counter/ stacker

1 x Used Wrapping Machine WM FC780 E, age 2005, Unwinder:, Single Reel holder, Max. reel diameter 1,200 mm, Thermoforming machine:, Max. tool size 780 x 570 mm, Max. tool size with pneumatic clamp frame 750 x 570 mm, Max. positive depth 130 mm, Max. negative depth 130 mm, Max. sheet width 810 mm, Max. sheet indexing 570 mm, Max. HIPS sheet thickness 1.8 mm, Max. EPS sheet thickness 3 mm, Max. platen stroke (upper – lower) 150 mm, Heater length 1,775 mm, Clamping force DaN 20,000, Upper heating, installed power Kw 41, Lower heating, installed power Kw 41, Vacuum pump motor Kw 2,2, Platen driving servo motor (each) Kw 7.5, Sheet index servomotor Kw 11, Dry cycle speed 45 Cycles/ min, Processing air pressure 7 bar, Water consumption at + 12° C. 60 L/ min, Air consumption at 7 bar 50 L/ cycle, Cutting Press:, Max. cut dimensions 760 x 550 mm, Platen clamping force DaN 60,000, Upper platen ...

ILLIG RDM70Kb Mold for PP Cups, Ø73 mm 32 Cavities, complete with Stacker Basket with Rods & Brushes & Rake, age May, 1997., Manufacturer: MARBACH

BVM Compacta 5022 EGS Sleever, age 2014, Infeed flighted Conveyor length 1200 mm (approx.), BVM grouping System:, For production of multipacks of unto 4 Stacks side by side, consisting of:, Transport conveyor, width 400 mm, length 1000 mm (approx.), 1 Rake on top with mechanical positioning via frequency converter in servo mode, Including pneumatic flap for producing multipacks of 2, 3 or 4 Stacks, The transfer of single Stacks is also possible., Max. length of Stacks 630 mm, BVM fully enclosing packing/ Sleeving machine Compacta 5022. Fully automatic, fed by conveyor belt with photocell control, including 100 format-data storage locations, Technical Data:, Service side standard : left had side, Sealing length : 500 mm, Passing Height : 220 mm (standard), Belt width infeed/ outfeed conveyor : 400 mm, Speed : upto 120 cycles/ min , Length sealing : continuously working, Film width max. :  ...

1 x Used ILLIG RDM70K PP-Mold, 5-Cavites, Strawberry Containers 174 x 103 x 90 mm, age December 2005. Product drawing is attached.

AVIAN Engineering Grinder G46/ 60, Age 2003 Consisting of :- Driven Infeed Pinch Rollers Main Motor 20 kW Blower Motor 2 kW Rotary Blade 6pcs Stationary Blade 4pcs Through-Put 300 KG/H Cutting Chamber 620 x 460 mm Hopper Opening 620 x 500 mm, With Blower Good Production Condition. EXW our Warehouse Enger, Germany

Spare Parts for Printers and Thermoformers Consisting of :- GABLER 702/703 Complete Control Cabinet ILLIG VHW 72 Infeed Adjustment VAN DAM Vane Vacuum Pump Norgren Plugassist Cylinder Skeletal Waste Material Winder 20 x ILLIG RDM 70K Mold Parts for 68mm PP Cups 1 x Plastic Crate Polytype DDM 300 Spare Parts 2 x VAN DAM Goose Neck Cup Feeder, 1 x Inclined Conveyor Cup Feeder 8 x Plate Cylinder Assembley Polytype BDM 301R

ILLIG RDM75K Thermoformer age 1998, refurbished in 2019 with Siemens S5 PLC Controls, used only for ca. 50,000 hrs, Consisting of:, ELAU B1 Display with Touchpad controls Thermoformer with auto-start facility Indramat Servomotor Indexing Max. material width 750 mm Max. Indexing length 480 mm Top & Lower heaters, total connected load top & bottom heaters 111.3 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 700 x 450 mm Hydraulic Cylinder Plug Assist with Bosch Rexroth Hydraulic Power Pack, completely Overhauled in 2019 Max. Part height 150 mm Max. Mold closing force 25,000 daN Auto Lubrication system Siemens S5 PLC Controls New original ILLIG/ RITTAL Control Cabinet Cooling System added in May-2023., No Tooling or Format Parts are included with the Line., Max Stacking Area: 750 x 350 mm, Min dia. of product: Ø 40 mm, Max dia. of Product: Ø 150 mm, Total Dri ...

1 x Used ILLIG RDM70K PP-Mold for 8-Cavity, Rectangular Containers 145.5 x 65.3 x 41 mm age December 2007. Product drawing is attached.

: 250 m³/min: 200 mbartotal power requirement: 5,5 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

carrying capacity: 1600 kgnumber of suction cups: 10 weight of the machine ca.: 180 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Age: 1994, For sale outside Europe, Consisting of:, Automatic Elevator Tray-feeder Cross Conveyor to main Print unit Universal screw Denester CUBITRON Corona Pretreatment System 8-mandrel Indexing Turret, with Mandrel Holders for Cups 6 x individually hinged dry-offset Print Heads Each Print Head consisting of Print cylinder, radial and axial Print adjustment with micro-register during operation of the Printer, 2 x Form Rubber Rollers dia. 71 and 100 mm 2 x Oscillating rollers 2 x Idler Rollers 1 x Ink Transfer roller (Ductor Roller) 1 x Ink Fountain, Ductor Rollers water cooled Ink Washing System on Print Heads UVITERNO Dual Lamp UV Curing-On-Mandrel Dual Belt Take-off with Air Assist Short conveyor to counter Stacker station Return Elevator Tray Feeder, Printer in production with Yogurt Cups at 444 Cups/ min Siemens SIMATIC S5 PLC Controls V. Good Production Condition, can be inspected ...

Used ILLIG STAL80 Trim Press, age 2004:-, Technical data ILLIG STAL 80 :, Punching table area max. 1000 x 510 mm, Material width max. 800 mm, Infeed length 20 - 400 mm, Stroke height 200 mm, Mold height 272 mm, Part height (positive and negative) max. 100 mm, Number of strokes (infinitely variable) 25 - 130 /min, Trimmed Parts are stacked through the Punch Tool, The Skeletal Waste is fed directly into the Grinder, Punching pressure 20 000 daN, Drive capacity 4.16 kW, Servomotor Indexing of sheet, Laser control Technology for v. low tolerances in the difference in the Hole Punch Position, ILLIG RS75 Under the Trim Press Grinder, Motor 8.3 kW, Condition: v.good, Condition: v.good

Age 2003 Consisting of :- Max. Infeed width 900 mm Throughput 500 Kg/ hr Main Motor 15kW Pendulum Roller for infeed tension control Dual Roll Ingfeed, Motor 0.75kW Regrind Outfeed Blower type F-25 , Motor 2.2 kW No. of Rotor Knives 3 No. of Stator Knives 3 Sound Proof Housing

Age 1990, refurbished in 2003 Consisting of : With auto-start facility Unwind Stand Indramat Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump Inline ILLIG UG70b Counter/ Stacker, with delivery conveyor Inline Grinder with Blower EXW our Warehouse Enger, Germany, max. mateerial width: 730 mm, max. Form Area: 680 x 280 mm, Infeed length: 300 mm, max. draw: 125 mm

Age 1988:- Technical data ILLIG STAL 80 The ILLIG STAL80 can work Inline with any Thermoformer, or it can be used Off-Line as a stand-alone Trim Press. In Stock at our Warehouse in Enger, Germany, Punching table area max: 1000 x 510 mm, Material width max: 800 mm, Infeed length: 20 – 400 mm, Stroke height: 200 mm, Mold height: 272 mm, Punching pressure: 20 000 daN, Drive capacity: 4.16 kW, Total length: 3950 mm, Total width: 2385 mm, Weight approx: 3600 Kg