mills used for sale

60” x 22” Two Roll Mill Manuf.: Bridge UK With variable speed control Siemens S7 - 1200 Safety PLC. Danfoss 90kW 315 Amp Frequency Drive with Dynamic Braking Resistor Electromotor 90kW 980rpm Front Roll Speed max. speed (50Hz) 14.1rpm Manually adjustable guide plates Manual nip adjustment Failsafe Pneumatic Caliper brake for Emergency Stopping of Mill Flood cooled rolls with rotary unions fitted 8 outlet mechanical lubrication system to roll bearings David Brown gear box – ratio 980:65.1 High speed pinion / bull wheel drive to rolls Safety PLC control for Start up sequence and machine monitoring HMI fitted to main panel for status monitoring of machine Operation Controls – Rolls Stop / Rolls Start / Inch Reversetart / Inch

Robinson 60” (1500mm) x 22” (550mm) Two Roll Mill Hand operated nips Water cooled rolls Rotary joints for steam heating / water cooling Electric Autostop (kicked reverse stop) Lunn Safety Bar Bull wheel drive The Mill sits on a fabricated bedplate With Gearbox, Motor and Control Panel

Two Roll Mill 42inch wide x 16inch diam. Right angle drive Brook Crompton Motor 50HP Lunn Safety Bar front and back of Mill Hand operated nips Compact

1 x Rodolfo Comerio 2200mm wide x 700mm dia two roll mill, Year of manufacture: 1981, motorised nip adjustment, Rollers bearings, Direct drive gearbox (no bullgear) With 138Kw DC variable speed motor and controls Stip knives to back roll?. In very good condition.

GINES, Barcelona 800mm wide x 350mm dia two roll mill, Machine number: 88, manual nip adjustment, adjustable guide plates, friction ratio 1:1.18, direct drive gearbox (on left hand side), with 60HP DC variable speed motor, Mentor II DC drive control panel. O/a dimensions 2750mm x 2100mm.

AGICOM recycling machines: Strong, very powerful single-shaft shredder for waste cables, scrap, paper/cardboard or plastic. Robust design, hydraulic pusher, easy replacement of the perforated screen, reversible blades Year of Make: 2021 Power: 30 kW; 400 volts

M. No.: 0392 Equipment / Additional information: Feeding width (mm): 500 Kw: 7.5 A: 380

Used only for experiments.

Year of construction 2006 Rotor width: 600 mm Drive motor: 50 kW Rotor has been overhauled, blades have been replaced with spare knife + spare sieves without control cabinet, the machine was connected to a central control cabinet

large plastic mill. Note: The operating hours are unknown. The entry 99999 hours is only pro forma and does not correspond to the actual hours Delivery by pick-up and disassembly on site

Wittmann Mill

A total of seven identical Tria S.p.A. plastic granulators are available. Rotor knives: 3, stator knives: 2, rotor diameter: 260mm, motor power: 7.5kW, throughput: 150kg-220kg/h, hopper opening: 350mm/300mm, hopper capacity: 30l, discharge hopper capacity: 15l. Machine dimensions X/Y/Z: approx. 1200mm/800mm/1750mm, weight: approx. 650kg. Documentation available. On-site inspection is possible.

Dreher Delta 20/40 granulator for the size reduction of injection mouldings or hollow plastic bodies with a medium cross-section, rotor diameter 200 mm, working width 400 mm, 3 rotor blades and 2 stator blades, infeed opening 200 x 400 mm, cyclone and bagging opening with a diameter of 304 mm, capacity 40-180 kg/h, electrical connection 400V/50Hz, connected load of granulator 7.5 kW, connected load of extraction 0.75 kW, connected load of control unit 1.0 kW, machine floor space approx. 2500 x 950 mm (WxD), machine height approx. 1950 mm, machine net weight approx. 800 kg

Number of blades: 6, rotor diameter: 350mm, engine power: 50kW, with construction as steel/welded construction in reinforced design and documentation, an inspection is possible, year of construction unknown, was overhauled in 2022.

Number of blades: 6, rotor diameter: 350mm, engine power: 50kW, with construction as steel/welded construction in reinforced design and documentation, an inspection is possible, year of construction unknown, was overhauled in 2022.

A Getecha plastic granulator is available. Rotor diameter: 300mm, cutting width min./max.: 400mm/1260mm, number of rotor knives: 5, power: 5.5kW. Including an enlarged control cabinet. Overhauled with less than 100 operating hours. Documentation available.

Rotor diameter: 450mm, cutting chamber opening X/Y: 900mm/540mm, rotor blades: 3 x 32, stator blades: stationary, drive power: 37kW, throughput: 900kg/h, machine dimensions X/Y/Z: approx. 1600mm/1700mm/1500mm. Documentation available.

Two low-speed Zerma beside-the-press grinders are available. 1) Zerma GSL-180/430, year of manufacture: 2003, rotor diameter: 180mm, rotor width: 430mm, rotor speed: 150rpm, drive power: 4kW, number of rotor knives: 45, number of stator knives: 2, min. sieve hole diameter: 5mm, weight: approx. 250kg. 2) Zerma GSL-180/300, year of manufacture: 2003, rotor diameter: 180mm, rotor width: 300mm, rotor speed: 150rpm, drive power: 4kW, number of rotor blades: 30, number of stator blades: 2, min. screen hole diameter: 5mm, weight: approx. 250kg. Documentation available. On-site inspection is possible. Individual sale possible.

A Rapid heavy-duty granulator is available. Only unreinforced polyolefins were ground with the mill, so it was not subjected to any load. Flour chamber opening X/Y: 1050mm/600mm, motor power: 75kW, rotor knives: 2x5, stator knives: 2, sieve: 8mm, throughput: depending on material. Machine dimensions X/Y/Z: approx. 2750mm/2100mm/2850mm, machine weight: approx. 4550kg. Documentation available. On-site inspection is possible.

Granulator Manufacturer: CONDUX Type: CS 300/600-4 WK Rotor 300 mm diameter x 600 mm wide 3 rotor blades, open rotor Housing with 4 stator knives With drive motor 11 kw (maximum 30 kw on request)

HERBOLD Fine Mill PU800 Suitable for soft to medium-hard materials Previously used for plastic fine grinding Grinding discs diameter 800 mm Drive motor 90 kw

For sale is a pulverizer that was previously used for fine grinding trials in the food sector. The machine is robust, reliable and powerful. Specifications: + Power: 7.5 kw + Processing capacity: 20-50 kg per hour + Weight: 450 kg Using liquid nitrogen, the machine is ready for immediate use. Just plug it in and get started. It is still in mint condition and can be restored by arrangement can be visited. The machine is sold plus 19% sales tax. If you are interested or have any questions, we look forward to hearing from you.

Manufacturer: HERBOLD MECKESHEIM Type: SMS 80/160 Rotor 800 x 1600 mm wide Drive motor 250 kw

Alpine RO 16/18

HERBOLD granulator type SMS 60/100 Heavy version Inlet opening 700 x 1000 mm Open rotor 600 mm diameter x 980 mm width optionally as an open 3- or 7-blade rotor Drive motor 110 kw Folding device with electric winch

Herbold Fine Mill PU 500 Suitable for fine grinding of plastics and soft to medium-hard materials Drive power 55 kW Grinding disc diameter 500 mm Throughput capacity approx. 200-800 kg/h depending on material and fineness

Granulator for heavy duty Make NETZSCH CONDUX Type CS 500/600-4 Inlet opening approx. 600x600 mm Semi-open 5-knife rotor, 4 stator blades Drive motor 75 kw

Granulator Dreher Delta 26/41 Stock No.: 503461 Machine/ Equipment Type: Granulator Manufacturer: Dreher Type: Delta 26-41 Year of manufacture: 2018 Enquiry form Enquiry by mail Specifications: - Lifelong dynamically balanced rotor system in turbine quality - Solid rotor with high momentum torque - Swivelling screen track and removal of the screen without tools - Solid steel bearing flanges with external bearing - Complete soundproofing booth made of non-combustible material - incl. cyclone separator Connector plug: 32A Throughput: max. 300kg/h Inlet cross-section: 260 x 410 mm Motor power: 11 kW Rotor blades: 5 Screen hole diameter: 10 mm Stator blades: 2

Used Rapid 2690-KURF Grinder, age 2005 Max. Infeed width 900 mm Throughput 500 Kg/ hr Main Motor 15kW Pendulum Roller for infeed tension control Dual Roll Ingfeed, Motor 0.75kW Regrind Outfeed Blower type F-25 , Motor 2.2 kW No. of Rotor Knives 3 No. of Stator Knives 3 Sound Proof Housing

Used Rapid 2690-KURF Grinder, age 2003 Max. Infeed width 900 mm Throughput 500 Kg/ hr Main Motor 15kW Pendulum Roller for infeed tension control Dual Roll Ingfeed, Motor 0.75kW Regrind Outfeed Blower type F-25 , Motor 2.2 kW No. of Rotor Knives 3 No. of Stator Knives 3 Sound Proof Housing