other machines for plastic used for sale (576)

Dryer / Centrifugal Dryer / Dry Cleaner Can be used for pre-shredded plastic waste (hard plastic, films), Throughput depending on the type of material approx. 0.5-2 t/h Drive power 30 kw

Laboratory heating press REITZ EHSP5H – used demonstration machine Heating press with pressing pressure 5 KN (0.5 tons) With heating device up to 200 °C from above and below. - Electric screw press press press force 5 KN (0.5 to) - Screw jack with spindle 20 mm, pitch 5 mm - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per revolution - Clear width approx. 60 mm - Pressing area 100150mm - Heating device with temperature control, 2 heating plates 100 x 150 mm - With TECO electric motor 0.18 KW - With reversing contactor control (up – down buttons) and emergency stop - Motor protection plug against overload, with main switch - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 100 kg . Suitable for foil bonding and embossing. Due to self-locking of the spindle, long holding time with constant pressure. The sc ...

Laboratory Heating Press EHSP20H – Used Demonstration Machine Table press / electric screw press with pressing pressure 20 KN (2 tons) With heating device up to 200 °C from above and below. Press drive with screw jack gear, reduction ratio 1 : 12, spindle diameter 32 mm, Pitch 6 mm, pressing area approx. 100 150 mm, clear height and stroke approx. 300 mm. Geared motor 0.37 KW, 1,390 rpm, 4-pole, with spur gear i = 1 : 5, Speed 150 mm / min. Max. dynamic load 20 kN. With reversing control, control box and motor protection plug. Sturdy press frame made of steel. Undertable made of high-quality aluminium profiles 4545 mm, table surface 600600 mm, Table top made of multiplex board. Total weight approx. 100 kg. The table press has a pressing pressure of 20 kN (dynamic load). Typical applications are pressing work with exact lining. Suitable for pressing bonding, embo ...

Aluminium Z conveyor belt incl. mobile substructure Horizontal range 800mm (customizable) Rising range 2,000mm (customizable) 2. Horizontal range 800mm (customizable) Angle in the bend variable, infinitely adjustable Feed height: horizontal (individual) Discharge height individually adjustable Conveyor belt width 600mm (customizable) We supply our conveyor belts in PVC, PU, felt or rubber. PU conveyor belt incl. cleats and corrugated edge Drive: Motor 0.55KW ( customizable ), speed approx. 0.3m/sec Connection 220/240V, 50Hz protection class IP54 Drive etc. ready for connection, motor control optional 8x adjustable machine feet for alignment Scalloped edge: 50x25mm T-50 Cleat - 400mm pitch 2-layer particularly transversely stable The delivery time of an individual system is currently approx. 3-4 weeks, depending on the production effort. Our core competence lies  ...

Mixers for plastic granules and powdered products. Completely in stainless steel. Mixing motor 4 KW. Mixing chamber with separator on load cells. Pre-tank on load cells. Vacuum pump AZO 4 kW.

Mixer for granules and powdered products Mixomat. Completely in stainless steel. Mixing tanks on load cells. Tegiloxane pump. Vacuum pump AZO 5.5 kW. Granulate gate valve NW 100.

Granule dryer for heating and drying hygroscopic plastic granules. Tank capacity 1200 l. Heating capacity 9 kW. Optionally available with air dryer AZO LE 400 K

Dry air dryer Granulate dryer for drying and heating hygroscopic granules. Capacity 600 l. Heating capacity 4.5 kW. Optionally available with dehumidifier AZO LE 600 P.

Semi-automatic drilling device for plastic parts This purely pneumatic drilling device is designed for repeatable drilling of small plastic parts up to approx. 40 x 200 x 40 mm with holes up to 3 mm. Specifications: - Linear axis travel 420 mm - Stroke approx. 30 mm - Height adjustment approx. 100 mm - With 2-hand release - Plexiglass protection on 3 sides - Emergency stop switch - Sturdy, mobile frame made of aluminium profiles - With 4 swivel castors, 2 of them with brakes - Overall dimensions approx. 1000 x 1000 x 1700 mm - Weight approx. 50 kg - With collet for drill bit 1.5 mm Expiration: - Setup: Adjust stop angle to part size - Setup: Alignment of cross table in X and Y - Setup: Set height adjustment to part height - Inserting the part - Triggering via 2-hand button and holding until drilling is completed - Removal of the finished part and placement  ...

Fully automatic hot stamping press Oropress Mechanical eccentric press with lift table Lift table as pneumatic sliding table 250 x 250 mm Fully automatic sequence, optionally triggered with foot switch for single stroke Heated press punch 120 x 200 mm up to 250 °C Safety grille Film Feed Unit Built in 1986

Base Machine is a OMSO DM44N 2-Lane Lid Machine, age 2004, L- Format in feed conveyor for feeding Vertical Lid Stacks, acts as an accumulator as well Auto feeding of Lid Stacks to the 2 x Universal Screw Denesters with suction Nipples Infeed conveyor with Vacuum to keep Lids in proper position Each Lane with PAGOmat 6HS Pressure Sensitive Label dispensers, with PLC Controls, manufactured by PAGOmat/ Fuji Seal, Switzerland Outfeed Conveyor to 2-Lane Lid Stacker 2-Lane Stacker, each Lane with 2 x Universal Helical Screws Main Drive with a variable frequency, AC-Synchronous Motor with a brake, with Microprocessor Controls Max. dia. of round Lids: Ø125 mm Max. dimensions of Rectangular & Oval Lids: 125 x 150 mm Max. height of Lids: 25 mm Speed with Oval Lids dimensions 120 x 130 mm: Single Lane 110 Lids/ min, Dual Lane 220 Lids/ min 400 V, 3 phase, 50 Hz

Electric surface press REITZ EHSP522 Pressing surface 200200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press

Data sheet heating press Oropress Pneumatic press 5 KN / 0.5 tons Press stroke 50 mm Adjustment of the clear height with handwheel and spindle, adjustable from 100 to 220 mm. With top heating plate 120 x 100 mm and temperature control, temperature up to 250 °C. Pneumatic two-hand control with triggering via Festo ZSB. Pneumatic sliding table 180 x 220 mm for loading outside the machine. Machine dimensions W = 1100 mm, L = 700 mm, H = 1850 mm Machine weight approx. 300 kg Movable on castors On request for an extra charge with second heating plate and temperature control at the bottom.

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Comexi solvent-free laminating system Coating width = 1320 mm , Speed = 350 m/min, With 2 unwinders (turnstile) With 1 rewinder (turnstile) With Doypag vario mixer. Mixing plant 4 heaters Pre-treatment AFS corona type. G 60 S,

Rotor diameter: 500 mm Rotor width: 1200 mm kW: 30

EPS contour cutting line for the production of sloping roof, fillet and ridge panels, as well as freely programmable "contours". suitable for net block dimensions: 5300 x 1300 x 1300 mm. Version with oscillating panel cutting frame for the production of EPS sheets and special cuts. incl. block turner incl. automatic wire adjustment incl. trimming frame incl. plate chain conveyor incl. waste disposal incl. wire break detection (electronically controlled) incl. extensive documentation Visits are possible at any time by arrangement.

Bottom weldig machine with slit selimg up to 4 webs, unwinding, side gusseting, hole punching, collecting belt, max. welding width 1300 mm, draw length: 220 - 1300 mm, cycles (mech.) max. 220/min, very good condition, video availabale

Plastic compactor Main drive 132 kW Complete system with recutting mill, fine material separation and recirculation, electrical control

Automatic machine Bag machine for the production of bags on roll. Capacity 50 bags / minute (depends on the size) Machine width 1200 mm Unwinder width = 1200 mm (tubular film) Core Magazine Folding unit for C folding Floor welding and perforating unit Automatic winder (turnstile) with automatic sleeve feed

Electric spindle press REITZ EHSP100F as laboratory heating press / demonstration machine Laboratory heating press with pressing pressure 40 KN (4 tons), ratio 1 : 16, spindle diameter 45 mm, pitch 8 mm, spindle stroke 0.5 mm per revolution. Gear motor 0.75 KW, 1,500 rpm, 4-pole, with spur gear i = 1:5, Speed 150 mm / min. Max dynamic load 25 kN. With reversible control, emergency stop and motor protection plug. Total weight approx. 100 kg, table surface 600 600 mm, pressing surface approx. 150 250 mm, clear height approx. 60 mm. Base made of high-quality aluminium profiles 4545 mm, the table top is made of glued plywood top. The laboratory heating press has 40 kN pressing pressure (dynamic load). The spindle is self-locking and thus maintains the pressing force for a longer period of time. For an extra charge with heating plate, insulating plate and temperatur ...

Eos EOSINT Here we offer an Eos EOSINT plastic laser sintering system. The following things are included with the EOS P380 system Installation space containers Powder containers Overflow container Cooler: Termo TEK Termochiller Type: P411-12448-1 3DM 8 zones process chamber heating 250°C Each zone individually adjustable, homogeneous temperature field ± 1°C Kelvin 350mm x 350mm x 610mm Sannung 3/N/PE/ 400V AC Frequency 50 Hz Current value 8 kW Fuse 32 A MAX Power Laser 100 W Laser class open 4 Laser class Closed 1 Weight 850 kg Type: EOSINT P 380 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information reserved!) We are happy to answer any further questions you may have on the phone.

3D-SYSTEMS ProJet 660 Pro 3D Printer Here we offer you a 3D-SYSTEMS 3D printer. The ZPrinter ProJet 660 Pro 3D printer has a large installation space. This means that even large models can be produced without prior cutting. Furthermore, the large footprint increases productivity when printing many small models in one printing process. 3D color printers with tremendous productivity and color fidelity. The ProJet ColorJet color 3D printers from "3D Systems", also known as ZPrinter, work layer-forming according to the ColorJet CJP "Binder Jetting" process, directly in a powder bed. As a result, even with complex and detailed printouts, these 3D printers do not require dedicated support structures. The non-solidified powder supports the components during printing and is then recycled semi-automatically. Applications Communication of form and design, installation analyses, first fun ...

machine measurements: 9.657 x 1.472 x 1.985 mmmachine weight: -- kgpower capacity: -- kWCondition: used - as good as newSpecification: FFP 2 N95 mask system completeConsisting of:- see sketches in the plant- cycle time approx.: 35 - 50 pieces/min- not CE certified- Space requirement approx.: 9,657 x 1,472 x 1,985 mm- Completely assembledThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

With the three-head roller saw, plastic-coated films can be sawn from wide roll to customer roll. With the system, film rolls can be sawn on 3" and 6" cardboard or plastic sleeves. The first cutting head is firmly positioned and defined as a master. The other two cutting heads are positioned to the master on the desired cutting width. A maximum of 2 benefits are possible. Sawing operations can be sawn dry, or wet by a wetting device of the saw blade. • Mesh type: Saw Material: Foil • Cutting system: circular saw s600 mm ( 3 saw cuts ) Saw cutting width: 6mm • Space usage: 7m x 4m Dimensions machine: 4.20m x 2m (height closed 2.15m, open 3,50m Sleeve width max.: 2700mm Cut width max.: 2620mm Cutting width min.: 500mm • Rolls max. : 550mm • Rolls min. : 200mm Sleeve diameter: 76mm/152mm

see pdf attached

Laminating unit (not complete machines) The machine is used for the coating of a product web with simultaneous Laminating a second goods railway. Products = 200-800my PET with 40-80 my PE Working width max. = 1600 mm, Speed = 70 m / min Approximately 1000 operating hours New price approx. = 400,000 euros) Accessories: 1x Barrel melter 1 x storage unit 50 liter / 86 KW Nozzle

Conveyor belt / belt conveyor Belt width: approx. 300 mm Axle distance: approx. 3,130 mm Drive: 0.75 kW new - only very short in use

Conveyor belt / belt conveyor Belt width: approx. 1,400 mm Axle distance: approx. 8,000 mm Drive: 2.2 kW

Cooling tray type KW 1000-200-200 self-sufficient for strand cooling in the production of granules or filaments. - a mobile and height-adjustable base frame made of welded steel raw, left machine version, painted - Frame-height adjustment of the top edge of the water bath from 900 mm to 1050 mm - a VA cooling tray 1000x200x200mm - 2 pieces adjustable and mounted strand holder - clamped to water edge - 1 piece wiper bled for partial strand drying - 1 piece of adjustable tub plug for filling height adjustment - 1 piece of VA water tank (reservoir) as service water tank - 1 piece of bacon water pressure pump to supply the cooling tank with sufficient cooling water from the water tank - 1 piece of direct 1/2" fresh water connection via float switch and solenoid valve for connection to the customer's side Fresh water network - Tub overflow - drain pipe DN50 for connection to ...