sheet metal working used for sale (3,314)

plate thickness: 4 mmblade length: 220 mmpressure: 0 tweight of the machine ca.: 1,5 tdimensions of the machine ca.: 1,6 x 1,7 x 1,6 mtotal power requirement: 2,5 kWCombined notching machine with a fixed 90° angle and an adjustablerectangular notching unit variable up to 200mm length x fixed 100mm width.There are 2 manually adjustable stops with a digital display.Axle length X900mm / Y300mmThere is no stamp holder / punch / hold-down device for this.These parts can be purchased from Boschert.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 3-4 mmpressure: 0 tCutting length: 220 mmtable height: 900 mmquantity of oil: 35 lTable dimensions: 950 x 790 mmtotal power requirement: 4 kWweight of the machine ca.: 0,95 tdimensions of the machine ca.: 1,0 x 0,86 x 1,2 mFoot switch angle adjustment 30°-140° automatic cutting gap adjustmentThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 220 kNsheet thickness - max.: 8 mmtravel -x axis: 2500 mmtravel -y axis: 1250 mm: 90 m/min: 60 m/min: 108 m/min: 360 °/secpunch diameter: 76,2 mmworkpiece weight: 150 kg: 0,01 mm bzw. 0,01° : 15 Stücktool changing time: 1,5 - 6,5 secweight of the machine ca.: 11.050 kgdimensions: 6400 x 5800 x 2100 mmWorking hours: 30.430 hThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2500 mmplate length: 1250 mmplate thickness: 8 mmPunching capacity: 220 kNNumber of working hours: 51.658 htotal power requirement: kWweight of the machine ca.: 11.050 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 6 mmpressure: 18 tblade length: 220 mmangle adjustable from - to: 90 Gradtable surface area: 1100 x 950 mmchamfer lenght: 835 mmtotal power requirement: kWweight of the machine ca.: 1,1 tdimensions: 1,2 x 0,8 x 1,4 mCombination machine: edging and notching- foot switch- Emergency stop switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

open-circuit voltage: 280 - 320 VDCcurrent intensivity: 30 - 80 Aoutput voltage: 140 VDCcutting medium: Air / Nitrogen total power requirement: ca. 11,2 kWweight of the machine ca.: 40 kgdimensions of the machine ca.: 0,90 x 0,35 x 0,50 mPlasma Cutting MachineHYPERTHERM - Hypertherm Powermax 1100incl.HYPERTHERM RT 80 hand torch- Recommended cutting capacity: 22 mm- Maximum cutting capacity: 29 mm- Severing capacity: 38 mm- Gas: Air or nitrogen- Gas inlet pressure: 6.1 bar- Gas flow rate: 189 l/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3200 mmplate thickness: 3.0 mm STthickness at Niro-steel: 2.0 mmOpening width / upper beam: 300 mmspeed: OW 40.0 mm/secBending beam adjustment: 80.0 mmspeed: BW 90.0 Grad/secwork height max.: 900 mmcontrol: MULTIBEND 5000 back stop - adjustable: 10 - 1550 mmaccuracy +/-: 0.1 mmair pressure: 5.0 barNumber of working hours: ca. 1.000 htotal power requirement: 2x 4.0 kWvoltage: 400 Vweight: 4400 kgrange L-W-H: 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours () good condition () Special price on request- in checked condition - machine video -https://www.youtube.com/watch?v=VP6emx4HTYM! Maximum flexibility when bending cassettes, boxes and profiles! High flexibility in bending part design! High productivity and throughput! Easy to useEquipment:- motorized universal swivel bending machine RAS 73.30 high-precision mechanics with  ...

sheet width: 1350 mm: 3 mmsheet thickness for stainless steel: 1,5 mmrear stop: 600 mmtotal power requirement: 3 kWweight of the machine ca.: 1150 kgdimensions: 2030 x 1940 x 1220 mmStandard equipment:- All-steel welded construction with static and dynamic frame rigidityframe rigidity- Direct drive with brake motor- Specially alloyed cutting blades- 750 mm motorized, digitally adjusted backgauge with ball screwsrecirculating ball screws- Manual blade gap adjustment system- Mechanical sheet clamping system with plastic base- Work table with insert plates- foot switch for single and repeat cutting cycles- 1 x squaring arm 1000 mm long with metric scale- 2 x 800 mm front material support arms- Front stop- Finger protection - front and rear covers- Rear light guards- CE declaration of conformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2600 mmplate thickness: 10.0 mm STpre-bending: 8.0 mm STdiameter of upper rolls: ~ 220 mmside roll diameter: ~ 170 mmdiameter of lower rolls: ~ 190 mmControl: konv. oil volume: 80.0 Litervoltage: 380 Vtotal power requirement: 5.5 kWweight: ca. 5000 kgDimensions (only the machine): ca. 3500 x 1550 x 1400 mm very good condition () current new price incl. accessories approx. 120.000 Euro special price on requestEquipment:- robust electro-hydraulic 4-roll round bending machine- 4-roll concept offers a wide range of bending and rounding options- Swivel-mounted control unit Operation - control of all rollers or machine axes Digital position display of the side rollers Manual operation via JOY sticks- Two central rollers are driven directly via hydraulic motors- Conical rolling possible by tilting the rollers- Parallelism of the side rollers via torsion shafts- Bending on both side ...

sheet width - max.: 1020 mmplate thickness: 1,5 mmcutting length: 1020 mmweight: ca. 300 kgdimensions of the machine ca.: 1,3 x 0,8 mCondition: good, demo machine: Side stop: 600 mmMaterial place of deposit: ausziehbar Hand lever shears with counterweight, length stop, blank holder withQuick clamping, mm scale on the table, pull-out sheet metal support.Demonstration machine at a special price.Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 6 - 28 mmwall strength: 2 mmbending radius min.: 2 x D Control: IPU 20 bending radius max.: 5,0 x D mmbending angle max.: 190 °arbor length: 3000 mmoperating pressure: 180 barhydraulic motor: 4 kWweight of the machine ca.: 900 kgdimensions of the machine ca.: 3,8 x 1,1 x 1,3 mCondition: ready for operation: Video available on our website.: Electric 400 Volt: Bending segments: 15-20-26-28 mmBending mandrels: 4 Operation panel: 0,5 x 0,6 x 1,03 mDouble Foot pedal: Machine manual: Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut.Mandrel lubrication, adjustable length stops.Operating modes: MANUAL and semi-automatic.Co ...

engraving field: 120 x 120 mmtable-size: 250 x 250 mmworkpiece weight: max 50 kgControl: Fobagraf machine weight ab.: 1000 kgmachine frame made of welded steel constructionCross slide, hard stone design, table top with steel stop ironHeight-adjustable laser headQuality-switched ND: YAG laser head, lamp-pumped, 100 WDeflection unit mounted on the laser head (with standard lens)Z-axis with gearbox and servo driveServo axis control with X-, Y-, and Z-axesWater-cooledControl: Fobagraf user software packageOperating system: Windows 2000operating hours: 17.388 hmanual includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1300 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1600 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3020 mmplate thickness: 5 mmdistance between columns: 3020 mmControl: Simatec OP7 stroke: 450 mmback stop - adjustable: 1000 mmwork height max.: 900 mmtotal power requirement: 22 kWweight of the machine ca.: 9000 kgdimensions of the machine ca.: 4200 x 1600/2900 x 2000 mmFeatures:- Motorized backstop, 1000 mm- Motorized upper crossbar adjustment- Motorized lower crossbar adjustment- Side protection- Foot switch- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3000 mmplate thickness: 4 mmwork height max.: 900 mm: 450 mmtotal power requirement: 5,5 kWweight of the machine ca.: 4800 kgdimensions of the machine ca.: 4250 x 1500 x 1850 mmEquipment:- electric bending angle adjustment- electric upper beam adjustment- foot switch- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3240 mmplate thickness: 2,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 3,00 tdimensions of the machine ca.: mManual and automatic bending operation possibleBending angle adjustable via potentiometerUpper beam stroke height and material thickness selectable via DIP switchesBending rail and machine in excellent conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3050 mmplate thickness: 6 mmrear stop: 10-1000 mmcutting angle: 0,5 - 2,5 °down holder: 20 Stkno. of strokes: 14 - 23 Hub/minwork height max.: 900 mmoil volume: 140 ltotal power requirement: 11 kWdimensions of the machine ca.: 4000 x 2150 x 1900 mmweight: 7800 kgEquipment:- ELGO control unit type P50- Automatic cutting angle adjustment- Automatic cutting gap adjustment- electric back gauge- Pneumatic sheet holding device- Light barrier behind the machine- 4 support arms- front finger guard- foot switch- Angle stop 0 - 180- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 34 mmsquare edge steel: 30 x 30 mmL-beam: 100 x 10 mmflat steel: 100 x 14...160 x 11 mmblade length: 175 mmT-beam: 100 x 10 mmnotching: l + T material: 10 mmhole punhing press: pressure: 45 tthroat: 305 mmtotal power requirement: 3 kWweight of the machine ca.: 1,2 tdimensions of the machine ca.: 1,4 x 0,8 x 1,5 m 5-fold combinated profile steel shear incl. flat steel shear profile steel shear bar steel shear notcher hole punch 2 foot switches contact limit stop various punching saddles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 135 tchamfer lenght: 3100 mmdistance between columns: 2600 mmcolumn arm: 410 mmram stroke speed: 180 mm/secwork speed: 10.0 mm/secreturn speed: 135 mm/secwork stroke: 275 mmdayligth: 550 mmtable height: 900 mmtable width: 90.0 mmcontrol: ModEva 12S oil volume: 200 ltr.voltage: 400 Volttotal power requirement: 11.0 kWweight: 8800 kgrange L-W-H: 4250 x 2150 x 2800 mm current new price approx. 80.000 euros special price on request- in checked conditions - machinevideo - https://www.youtube.com/watch?v=ALo1SpWfnTk--------------------------- ------------------------------SPEED BEND electro-hydraulic press brake with : increased installation height increased cylinder stroke increased throat depth---------------------------------------------------------Equipmen t:- CNC electro-hydraulic press brake- CYBELEC ModEva 12S CNC control unit High-resolution screen Clear, concise menus in the ...

plate thickness: 6.5 mmthickness at Niro-steel: 5.0 mmangle adjustable from - to: 30 - 140 Gradno. of strokes: ca. 50 Hub/mintable:: 950 x 1030 mmblade length: 220 x 220 mmtotal power requirement: 4.0 kWweight: 800 kgrange L-W-H: 1100 x 950 x 1280 mm current new price approx. 20.000 euros good condition () special price on requestEquipment:- electro-hydraulic notching machine- multi-function machine with 2x work stations 1x notching, 1x unit for radius rounding including radius punching tools- manual angle adjustment 30 - 140 degrees 2x handwheels for angle adjustment- large / stable work table- 2x new angle stop, adjustable- automatic cutting gap adjustment- 1x freely movable foot switch- connection cable + 16A plug- cutting performance: 6.5 mm to 60° ST 5.0 mm to 60° VA 4.0 mm to 30° ST 3.0 mm to 30° VAThe data for this ad was created with ModulMWS - the software solution of LogoTe ...

sheet width: 2040 mmplate thickness: 3,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 2,30 tdimensions of the machine ca.: mManual and automatic bending operation possibleBending angle adjustable via potentiometerUpper jaw stroke height and material thickness selectable via DIP switchesManual backgauge with spring fingersThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 45 mmsquare edge steel: 45 mmL-beam: 12 mm: 40 flat steel: 450x15 mmL-beam 90°: 152x152x13 mm: 45 mmsquare edge steel: 45 mm: 12 mmweight of the machine ca.: 2323 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table width: 6000 mmtable length: 2000 mmburner heads: 1 Equipment:- Plasma source Kjellberg Hi Focus 161i- suction unit- CompressorTechnical dataKjellberg Hi Focus 161i plasma cutter:Cutting current at 100 % ED 10 - 160 AMarking current 5 - 25 ACutting range 0.5 - 50 mmPiercing up to 30 mmDimensions (L x W x H) 985 x 570 x 1140 mmMass 206 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

weight max.: 20 tworkpiece diameter: 1500 - 3500 mmdrum diameter: 250 x 100 mmfeed: 100 - 1400 mm/mintotal power requirement: 0,75 kWweight of the machine ca.: 2,5 tDimensions (LxWxH): 2,5 x 1,5 x 1,5 mRoller stand- Self-aligning- Forward/reverse rotation- New control system- Foot pedal- Emergency stop deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3050 mmplate thickness: 4 mmweight of the machine ca.: 6.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 1,7 mmroll diameter: 50 mmDimensions (L/W/H): 1600 x 600 x 1500 mmweight of the machine ca.: 400 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: tplate thickness: mmno. of strokes: Hub/mintotal power requirement: kWweight of the machine ca.: trequired space: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4 mmcutting angle adjustment: 30-120 °table height: 900 mm: 407 weight of the machine ca.: 760 kgdimensions of the machine ca.: 1300x1000x1150 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3050 mmplate thickness: 6 mmweight: 7.000 kgrange L-W-H: 3450x2200x1750 mmEquipment/accessories:- adjustable support table- Sheet support- angle stop- Sheet support arms- foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.