other metal working machines used for sale (11,093)

1 punching machine (14), manufacturer Kaiser, type KSTU 3500-25-6P, year of manufacture 2000, press force 350 t, stroke rate 20-100/min, stroke height 40 - 250 mm, ram adjustment 200 mm, installation height 700 mm, table size approx. 1,000 x 2,700 mm, control system, manufacturer Siemens, type Simatic Multipanel (retrofitted), force measuring unit, manufacturer Brankamp Marposs, type Prokos X1, two-hand operation, material discharge belt, downstream incline conveyor, coil unwinding reel, manufacturer Dreher, type 2380P, year of manufacture 2000, SN 0051, alignment unit, buffer section, belt feed, manufacturer Dreher, separate switch cabinet system, manufacturer Rittal, cooling unit, accessories: workbench, partition lighting, pull-out cabinet, swivel chair Find more here - / Contact us at -

1 press system, manufacturer Exner, type EXSBZRD 500/100, built in 2002, drive power 121 kW, pressing force 5,000 kN, overhauled in 2018, stroke length max. 600 mm, working speed max. 16/30 mm/s, machine weight 82,000 kg, table size approx. 1,000 x 3,000 mm, control system, manufacturer Siemens, type Simatic Multipanel, separate two-hand control, upstream light barrier, manufacturer Sick, separate control panel, manufacturer Rittal, control system, manufacturer Siemens, type OP17, feed unit, manufacturer AMT, type WV400/160, year of manufacture 2008,control panel, control unit, manufacturer Rexrodt, separate switch cabinet system, additional transfer unit/material feed, vertical material buffer, 6-fold feed-through unit, oiling, manufacturer Ratiol/Stöber Find more here - / Contact us at -

1 hydraulic double-column press (11), manufacturer: Exner, type EX100SBZR, built in 1988, power 42 kW, pressing force 1,000 kN, GG 11 Exner, type EX100SBZR, built in 1988, SN 10094, power 42 kW, pressing force 1,000 kN, GG 11,000 kg, overtravel 26 mm, table size approx. 900 x 1,100 mm, swivel chair, separate control panel, control system, manufacturer Siemens, touch panel, two-hand operation, manufacturer Sick, type XY2SB, front material feed, linear travel, approx. 1,000 mm Find more here - / Contact us at -

1 hydraulic double-column press, manufactured by Exner, type EX80SB, built in 1987, power 15 kW, pressing force 800 kN, GG 5,300 kg, overtravel 38 mm Find more here - / Contact us at -

table length: 175 mmtable width: 110 mmgrinding wheel diameter: 500 mmtotal power requirement: 1 kWweight of the machine ca.: 1,5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: PEAFFER Model: P160 H/I Power: 8 HP Voltage: 380 V Phase: 3 Frequency: 50 Hz Find more here - / Contact us at -

CNC vertical machining center Type: VF-9 D/40 HE Manufacturer: HAAS Year: 2006 Control: Haas X: 2134 mm Y: 1016 mm Z: 762 mm Table: 2134 x 914 mm Max table load: 1814 kg Max spindle speed: 10000 rpm Through spindle cooling Machine weight: 12837 kg In good condition, fully functional, under power Find more here - / Contact us at -

Manufacturer: HAEUSLER Model: HPR 330 V+H Year of Manufacture: 2007 Approximately 10 pallets of tools for round bar processing are included, with diameters of 60.5, 137, 91, 168, 76, 51, 152, 129, etc. Condition : Machine currently not in use and therefore not fully assembled Technical Data: - Maximum bending moment (at 240 N/mm² yield strength): 200–330 cm³ - Number of bending rolls: 3 - Roll arrangement: asymmetric / symmetric - Roll diameter: 520 mm - Driven rolls: all 3 - Roll drive: hydraulic - Working speed: 0–7 m/min, stepless - Speed compensation between upper and lower rolls: automatic - Roll rotation reversal: electro-hydraulic - Adjustable bending rolls: 2 - Adjustment of bending rolls: hydraulic - Roll position display: digital, 0.1 mm accuracy - Roll bearings: roller bearings - Number of pressure roller systems: 2 - Adjustment of pressure roller systems: hydraul ...

Manufacturer: AGIE Model: FUTURA V 1PM Electrical Specifications: - Voltage: 400 V - Frequency: 50/60 Hz - Phase: 3 PH - Circuit Breaker Power: 17 kVA - Power Factor (Cos φ): — - Full Load Current: 15 A - Full Load Power: 3.9 kVA - Amp Rating of Largest Motor/Load: 3.4 A - Overcurrent Protection: 20 A @ 480 V ~, 18000 AIC Weight: 265 kg Condition and Maintenance: Last service performed at the end of 2021 (running hours: 9107). The machine has been used only a few hundred hours since. Overall in good condition. Find more here - / Contact us at -

amount: 1 STKTool holderThese chucks are designed for high-speed machining.These are precision tools from the Italian company DAndreaThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 600 mmgear width: 500 mmmax. module: 15 min. module: 1 total power requirement: 2 kWweight of the machine ca.: 2 tdimensions of the machine ca.: 2x1,5x2 mThe rounding of the teeth is obtained by coordinating alternative movement of the cutter and rotary movement of the piece. The alternative movement of the cutter is obtained by rotating a cam, shaped in order to obtain radius or cusp rounding. A series of 4 cams allows to work modululus from 1 and 16 included. An regulation device allows change the modulus between the minimum and maximum value of every cam. The rotation of the piece is controlled by a three-stage gear wheel which forms the dividing system. The piece lock and the movement of the rapid entry of the cutter to the piece is controlled by pneumatic servo devices. The practicality and rapidity of the equipment, as well as the wide range of profiles availab ...

Manufacturer: Tox Pressotechnik Model: MAG 075.222.A.001 Year of Manufacture: 2008 Condition : Excellent Min./Max. Air Pressure: 0.3 / 0.5 MPa ; 3 / 5 bar Max. Press Force at Max. Air Pressure: 680 kN Total Stroke: 100 mm Power Stroke: 11 mm Machine Weight (without tool): 3420 kg Find more here - / Contact us at -

Manufacturer: ADIGE Model: LT652/B Year of Manufacture: 2002 Machine Description: - Tube laser system LT652, manufactured in 2002. - Equipped with a CO2 laser source with 2 kW power. - Loading length: 6500 mm - Unloading length: 3500 mm The machine is in good technical condition for its age. The cooling system requires occasional maintenance. Find more here - / Contact us at -