other metal working machines used for sale (11,583)

connected load frequency: 230 Vbattery: 24V / 100Ah Brush diameter: 510 mmturning speeds: 175 U/min0: Luft 24 L / stank capacity: 50 / 50 Literweight: 160 kgrange L-W-H: 1,1 x 0,52 x 1,0 mmDaewoo floor cleaning machine:Packed with battery and chargerTheoretical surface cleaning:Output: 2000 m²/hSuction width: 850 mmCleaning width: 510 mmMax. working area incline: 2%Fresh/waste water tank volume: 50/ 50 LThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

stroke: . mmweight max.: 300 kgspeed: . m/mintotal power requirement: . kWweight of the machine ca.: 2,5 tdimensions of the machine ca.: . mLoad capacity max 30 KNLoad moment 50 KNmTilt moment 93 KNmThe techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 10,000 items Accessories for your workshop.You want to sell machines, production lines or your company,then contact us.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

UV curing machine The product is a system designed for curing silicone. Due to the UV curing, the machine can probably also be used elsewhere. Manufacturer: Hereaus Curing: UV curing Operating voltage: 400 V Control voltage: 24 V Rated current: 16 A Fuse: 25 A Frequency: 50 Hz Year of construction: 2017 Among other components used: Heraeus P300MQ Motori Elettrici 71M/2 engine Condition: used Complete plant closure, large selection of mezzanines, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

WSM Stationary screwdriving unit screwdriving station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is surrounded by a protective enclosure. The service doors are equipped with interlocking monitoring switches. The doors are locked in automatic mode and can only be opened when the automazik stop or in manual mode after pressing the doors on the control panel. When the door is open, automatic operation cannot be started. Functional sequence The station is equipped with the pre-assembled assembly via the transfer belt. The work steps of the automatic station with a run of a WT are described below. In normal operation, all 3 stations work in parallel. - Positioning the WT with the pre-assembled assembly in St.2.1 - Lowering the wearer with the scanner and the vision sensor - Scanning of the 3 codes (front panel, fro ...

Glasbeek Finish Gas Chamber Furnace Type G.11.01 Glasbeek Finish Gas chamber furnace Type G.11.01 With loading trolleys Maximum temperature 200 ° C Year. 1991 3 x 380 V 54 kW Approximate internal dimensions (W1900mm x D2940mm x H1965mm)

With the device, upper and lower parts were previously joined together and pressed. Components are Kuka Scara KRC2sr Robot BJ 2010 Pneumatic control Electrical control with frequency converter 4 conveyor belts Description Robotor Type KR 5 scara R350 Working space volume KR 5 scara R550-Z320: 0.264 m3 Repeatability (ISO 9283) KR 5 scara R350: ±0.015 mm Reference point Working space Intersection of axes 3 and 4 Weight approx. 20 kg Datalatt Robot

CNC portal flame cutting machine Manufacturer: MGM Type: Cortina DS3100 Retrofit 2022 CNC control: MS300 Track width: 3,100 mm 1 oxy-fuel burner gas type as desired Track length: 5 or 6 m without table

filling capacity: 300 kgmax. workpiece height: 500 x 200 x 20 mmcontainer volume: 158 lworkpiece weight: 175 kgmax. workpiece weight: 15 kg / Stck.revolutions per minute: 22 U/minfilling amount: 40-50 %Colour: blau 5015 RAL0: 624 x 270 mmtotal power requirement: 1,5 kWweight of the machine ca.: 650 kgVideo available on our website.: Electric 400 Volt: New deburring machine for safe and to efficiently deburr workpieces.6 - angular drum lined with wear-resistant vulcanized rubber 36 mm, rollershutter to protect against the rotating container, stable design, simple service. Control panel with timer, hour counter, main and emergency stop switch and signal lamp. The maximum filling quantity is 40% of the containervolume andcorresponds to 300 kg consisting of 175 kg workpieces + 125 kg deburring medium = Hard manganese balls pic 6 or cast iron pentagons pic 7 (50 kg is included in the price) ...

0: . kgdimensions: . mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Equipment: 1 sledge feeder on the right 1 two-point eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 5.0 mm Belt width: up to 40 mm Feed length: up to 320 mm Power: up to 132 rpm

Equipment: 1 sledge feeder on the right 1 two-point eccentric press 70 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 3.5 mm Bandwidth: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm

Equipment: 1 sledge feeder on the right 3 press modules á 180 kN = 540 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 10 mm Belt width: up to 100 mm Feed length: up to 250 mm Power: up to 132 rpm

1 Wire bending machine OMCG date 1997 technical status good , soft ware to be refurbished 2.Tube bending machine OMCG date 1998 technical status good, software to be refurbished

Pipe furnace with 5m long furnace section for heat treatments under inert gas atmosphere. Tmax: 1300°C On the Nabertherm website you can see a product video of this unique stove. It was originally operated vertically as a downpipe furnace. A horizon-wide use is of course also possible. The structure is clear: It is a nearly 6m long truss-like frame, on which six oven case elements are attached. These are hinged and inside runs the almost 6m long pipe made of Kanthal APM. Each furnace element has two thermocouples type S (platinum/rhodium). Kanthal APM is very resistant to oxidizing atmospheres.

max. temperature: 1000 Gradsize of opening: 170 x 90 mmdepth of chamber: 280 mmtotal power requirement: 3 kWweight of the machine ca.: 80 kgdimensions: 0,7 x 0,55 x 0,72 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity: 2800 Wattvolume: 100 Lfilter: HEPA : 230 mbarmaterial: INOX Edelstahl Behälter: 5000 mmhose diam.: 32 mm: 5000 mmnoise: 82 dBdimensions: LxBxH 50 x 50 x 135 cmweight: 35 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

It is made for heat treatment of steel (originally 100Cr6 steel). Possible customers : automotive suppliers The last heat treatment on this line was made in 2018. For a better industrial usage, the supervision of the line need to be upgraded. The original constructor is FDI (Deleau Furnace), which was bought by ATI Furnace ati furnace nabertherm

It is made for heat treatment of steel (originally 100Cr6 steel). Possible customers : automotive suppliers The last heat treatment on this line was made in 2018. For a better industrial usage, the supervision of the line need to be upgraded. The original constructor is FDI (Deleau Furnace), which was bought by ATI Furnace ati furnace nabertherm Forge from 60 to 400 Ton Forging and Annealing Furnace

2018 Forge from 60 to 400 Ton Forging and Annealing Furnace ATI furnace It is made for heat treatment of steel (originally 100Cr6 steel). Possible customers : automotive suppliers The last heat treatment on this line was made in 2018. For a better industrial usage, the supervision of the line need to be upgraded. The original constructor is FDI (Deleau Furnace), which was bought by ATI Furnace ati furnace nabertherm

Saw blade chamfering machine Manufacturer: Loroch Type: AK Year of construction: 1991 For chamfering HSS and segment circular saws

Travel: 825 x 680 x 405 mm [ X x Y x Z ] Table size X: 1200 mm Table size Y: 850 mm workpiece weight: 3000 kg Electrode changer: 50 - fold Generator POCON 60 Pinole recording: EROWA Heavy Duty Adapter O-Module Halogen lamp

Travel distances: 350 x 250 x 315 mm [ X x Y x Z ] Table size X: 576 mm Table size Y: 400 mm workpiece weight: 500 kg C-axis Pinole recording: EROWA

number of controlled axis: - workpiece weight: - kgthroat: - mmtotal power requirement: - kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Qty. 1 Second-hand bifilar pipe winding line Mfc.: GRAEWE GmbH Type: AEW 1000 Built: 1998 Tube dia.: 10, 12, 14 & 16 mm Coil core ID: 940 mm OD: 1250 mm Bifilar coiler Type: EW 1000 PLC Simatic S5 Consist of: De-coiler Coiler Ring coiler Bending unit Support table Cutting shear Binding device Electrical Control

El. heated chamber furnace, make VEI type: VEI_KO_EB max. temperature: 450°C connected load: 28 kVA air flow: horizontal usable dimensions (w x h x d): 600 x 500 x 2000 mm

sheet width: 3050 mmplate thickness: 6 mmdistance between columns: mmblade length: 3050 mmtotal power requirement: 11 kWweight of the machine ca.: 7,6 tdimensions of the machine ca.: 2,1 x 3,3 x 1,8 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 5600 mmworkpiece height: 1500 mmtotal power requirement: 11 kWweight of the machine ca.: 150 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 0 mmy-travel: 0 mmworkpiece height: mmtotal power requirement: 0 kWweight of the machine ca.: tdimensions of the machine ca.: 0 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

groove width: 3 - 90 mmdrawing length: 430 mmworking speed: 4 - 12 m/minslot-milling length: 400 mmreturn speed: 15 m/mintotal power requirement: 5,5 kWweight of the machine ca.: 1,4 tdimensions of the machine ca.: 1,3 x 1,7 x 1,5 m• div. pull broaches and guidancesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

High temperature debinding furnace, make GERO type: HBO 50/13-3 2G heating: electrical useable space: ø400 x 400 mm temperature: max. 1.300°C ventilation: exhaust fan during the cooling phase and activated cooling fan ultimate vacuum: 10 mbar exhaustion time: ca. 5 min nitrogen: inlet pressure min. 3 bar oxygen: inlet pressure min. 3 bar