presses for wood used for sale (302)

press capacity:950 kNcontrol:Siemens S7 Required air-pressure:6 barloading area:1200 x 600 mmPressure power:1000 kNtotal power requirement:18 kWweight of the machine ca.:6200 kgdimensions of the machine ca.:2600 x 1300 x 3100 mm

Reading hours: 826 hours Auction-ID: A3-46156-16501

Used machine - completely overhauled - ready to use, no costs to be expected! BRIQUETTING PRESS Model No. E55 Year: 2010 Briquette diam. 55 mm, Engine kW 5.5 (High Efficiency). Production from 15 to 60 Kg/h. Dimensions: H 1.510 mm, 1.700 mm, 1.170 mm. Kg 600. Technical characteristics: Oleodynamic Machine; No. 7 Cycles per minute approximately with the machine at full speed; 3 cylinders; 1 Monobloc vice; Maximum length. of each expulsion 50 mm; 1 capacitive probe for working in automatic mode; 1 viewfinder; Shell diam. 1,000 mm. Capacity capacity ~ 0.73 m3; End-of-cycle device; Electronic pressure gauges, pump and vise; PLC Touch Screen Siemens; Siemens Display; hour meter; Inductive limit switches; Machine position control by LED; Stamping head; Preheating system; Oil and temperature level sensor; Current Stabilizer; Service keys; Voltage 400V – 50 Hz Stand ...

Technical details Manufacturer: MUP Model: 600 Machine number: 2014-375 Type: Briquetting press Configuration: - Fully automatic hydraulic briquetting system - Integrated hydraulic oil tank - Hydraulic oil heater - Hydraulic oil cooler with fan - Hydraulic oil filtration system - Vertical pre-compression unit - Hydraulic pre-loader - Reinforced stainless steel hopper - Agitator with anti-bridging drive - Screw feeder with 1.5 kW motor - Chain drive feed system Hydraulic system: - Pressing pressure: 225 bar - Automatic oil level monitoring Electrical equipment: - Supply voltage: 400 V / 50 Hz - Installed power: 37 kW - Control voltage: 24 V DC - Siemens S7-1200 CPU 1214C PLC - Siemens TP700 Comfort operator panel - IP54 electrical cabinet - Emergency stop - Optical barrier for automatic start/stop Feed system: - Loading opening: 415 × 920 mm - Hopper: 920 × 920 × 800 mm (approx. 150 l) ...

Pellet machine in working condition with signs of use - about 200-250kg per hour Auction-ID: A3-46152-22010

230V / 400V Foot and hand control. In working order. Auction-ID: A3-46152-6138

Not working - electrical fault. Power: 9.5kW Auction-ID: A3-46152-6144

\"Technical details Manufacturer: ITALPRESSE S.p.A. Model: XL/6 30-13 PM BO Type: Hydraulic hot press Year: 2017 Serial number: 191320317 Project number: 24465 Press configuration: 6-cylinder Press area: 3000 × 1300 mm Total installed power: 22 kW Supply voltage: 400 V Frequency: 50 Hz Phases: 3 + PE Full load current: 35 A Heating system: Thermal oil boiler Controller: MFD 80 digital control Construction: Hydraulic heated platen press Application: - Veneering panels - HPL laminate pressing - MDF lamination - Door production - Furniture component manufacturing - Wood panel bonding and pressing Dimensions: - Length: 3700 mm - Width: 1800 mm - Height: 2050 mm Weight: 5850 kg Certification: CE marked Condition: Used\" Auction-ID: A7-40557-5

- Four-column hydraulic press for pressing and die-cutting operations. - Nominal force 15 T. - Work table 1500 x 1200 mm. - Maximum opening approximately 1600 mm. - Four-column structure with vertical guide of the moving plate. - Upper hydraulic unit integrated into the structure. - Total installed power 11 KW. - Electrical panel with SIEMENS PLC. - Perimeter security guards with front access. - Integrated control desk and control panel. - Operating conditions of this item: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. Auction-ID: A7-48840-5

- Nominal force 400 T. - Dimensions of the work table approx. 1900 x 1500 mm. - Carriage stroke approx. 1600 mm. - The electrical control panel is incomplete; The rest of the machine's electrical installation remains installed. - Installation with access platforms for maintenance of the upper equipment. - Operating conditions of this item: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. Auction-ID: A7-48840-4

- Automated compression molding line composed of pre-press, main press, automatic loading and unloading system. - Hydraulic pre-press with clamping force 200 t. - Prepress work table 1900 x 1000 mm. - Approximate maximum opening of the prepress 1700 mm. - Main hydraulic press with closing force 600 t. - Main press worktable 2100 x 1600 mm. - Maximum aperture approximately 1750 mm. - Automatic parts loading system. - Automatic unloading system by means of an ABB 6-axis industrial robot equipped with handling tools for the extraction of parts. - Perimeter protection cabin with safety guards and interlocks. - Integrated electrical control panel and control desks. - Installation with access platforms for maintenance of the upper equipment. - Operating conditions of this machine: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those  ...

- Automated compression molding line composed of pre-press, main press, automatic loading and unloading system. - Hydraulic pre-press with clamping force 200 t. - Prepress work table 1900 x 1000 mm. - Approximate maximum opening of the prepress 1700 mm. - Main hydraulic press with closing force 600 t. - Main press worktable 2100 x 1600 mm. - Maximum aperture approximately 1750 mm. - Automatic parts loading system. - Automatic unloading system by means of an ABB 6-axis industrial robot equipped with handling tools for the extraction of parts. - Perimeter protection cabin with safety guards and interlocks. - Integrated electrical control panel and control desks. - Installation with access platforms for maintenance of the upper equipment. - Operating conditions of this machine: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those  ...

- Nominal force of 15 T. - Work table of approximately 1500 x 1200 mm. - Maximum opening approximately 1600 mm. - Ø 80 mm main thrust cylinder. - Four guide columns of Ø 95 mm. - Drive by upper hydraulic group with electric motor. - Equipped with SIEMENS SIMATIC OP7 control panel, PILZ safety controller and RAYTEK pyrometers for temperature control. - Electrical panel integrated into the machine. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. - Operating conditions of this item: unchecked. Auction-ID: A7-48840-9

Equipped with 10x pneumatic vertical press cylinder, 10x pneumatic horizontal press cylinder, Schmalz vacuum pump, Horizontal press bar for even clamping pressure over the full length, adjustable stops and clamps for different workpiece sizes, workpieces up to 4mtr, control box. Auction-ID: A1-48474-166

- Nominal force of 50 T. - Work table of approximately 1400 x 1000 mm. - Maximum aperture approximately 1150 mm. - Main thrust cylinder of Ø 150 mm. - Four guide columns of Ø 95 mm. - Drive by upper hydraulic group with electric motor. - Equipped with SIEMENS SIMATIC control panel, PILZ safety controller and OMRON electronic controllers. - Electrical panel integrated into the machine. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. - Operating conditions of this item: unchecked. Auction-ID: A7-48840-8

pressure: 250 tdistance between columns: 600 mmstroke: - mmtotal power requirement: 22 kWweight of the machine ca.: 9 tdimensions of the machine ca.: 2 x 2 x 3,2 mNo. 3421Mould press 2500 / 700 kNSingle stroke 2-handSingle stroke foot switchAutomatic continuous run set-up and tippingTable 500 x 500Working range: Pressure capacity 250 tonnesDrive: ^22The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 ttable surface area: 2100 x 1400 mmpassage width: 2122 mmtotal power requirement: 60 kWweight of the machine ca.: 35 tdimensions of the machine ca.: mPress/punch with injection molding unit200 ton punch upstroke press with injection molding machine (400to)Additional guard locking via 4 power strokesManufacturer: R+S TechnikYear of construction: 2013 / rebuild 2016Mains voltage/frequency: 400V/50Hz 3~(N/PEConnected load: 60KWWeight about 35000kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 600 tram surface: 3600 x 2500 mmstroke: 350 mmControl: Siemens S 7 no. of strokes: 11 - 44 Hub/mintable surface area: 3600 x 2500 mmram adjustment: 400 mmmaterial width: 500 - 1950 mmmaterial thickness: 0,6 - 2,5 mm mmcoil weight: 35 tcoil external diameter: 900 - 1900 mmcoil internal diameter: 610 mmno. of straightening rolls: 13 straightening roll diameter: 50 mmStack height: 400 mmstations: 2 total power requirement: kWweight of the machine ca.: 390 tdimensions of the machine ca.: mwith reel, Rstraight out Unit, (conveyor system Schleicher) and stacking unit(NSM)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 800 tdistance between columns: 3550 mmstroke: 1100 mmdistance table/ram, max. stroke up, adjustment up: 1900 mmtable surface area: 3500 x 1800 mmdie-cushion pressure inside the table: 350 tstroke of drawing cushion in table: 295 mmdie-cushion pressure in pusher: 80 tstroke of drawing cushion in pusher: 160 mmram surface: 3500 x 1800 mmdie-cushion inside the table: hydraulic, controlled die-cushion in pusher: hydraulic, controlled sliding table: without rails for travel total power requirement: kWweight of the machine ca.: 265 tdimensions of the machine ca.: moverhauled in 1998The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 600 tdistance between columns: 2600 mmstroke: 900 mmdistance table/blankh.,max. stroke up,adjustm. up: 1600 mmtable surface area: 2500 x 1730 mmdie-cushion pressure inside the table: 250 tstroke of drawing cushion in table: 400 mmdie-cushion pressure in pusher: 63 tstroke of drawing cushion in pusher: 150 mmram surface: 2500 x 1730 mmcolumn travel -side: 1100 mmdie-cushion inside the table: hydraulic, controlled die-cushion in pusher: hydraulic, controlled total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: moverhauled in 2005The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 800 tdistance between columns: 2560 mmstroke: 1050 mmcontrol: Siemens S5 distance table/blankh.,max. stroke up,adjustm. up: 1870 mmtable surface area: 2500 x 1730 mmdie-cushion pressure inside the table: 300 tstroke of drawing cushion in table: 395 mmdie-cushion pressure in pusher: 63 tstroke of drawing cushion in pusher: 150 mmram surface: 200 mmdie-cushion in pusher: hydraulic, controlled die-cushion inside the table: hydraulic, controlled total power requirement: 200 kWweight of the machine ca.: 150 tdimensions of the machine ca.: 4,95 x 3,3 x 10,2 moverhauled in 2005The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 1600 tdistance between columns: 3160 mmram stroke: 1450 mmdistance table/blankh.,max. stroke up,adjustm. up: 2250 mmtable surface area: 4000 x 2200 mmram pressure: 1000 tpressure of blank holder: 600 tstroke of blankholder at the bottom: 1000 mmstroke of blankholder with adjustment 0-100 mm: 1450 mmblank holder size: 4000 x 2200 mmdie-cushion pressure inside the table: 360 tstroke of drawing cushion in table: 275 / 400 mmram surface: 4000 x 2200 mmcolumn travel -side: 1100 mmdie-cushion inside the table: hydraulic, controlled die-cushion in pusher: hydraulic, controlled oil volume: 9000 ltotal power requirement: 390 kWweight of the machine ca.: 250 tdimensions of the machine ca.: 6,0 x 4,3 x 10,5 mHead press (1600 tons) of a press line with five subsequent presses (800 tons)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Work table 1600 x 1500 mm. - Maximum opening approximately 300 mm. - Main cylinder of Ø150 mm. - Four auxiliary cylinders of Ø80 mm. - Upper hydraulic group with 11 KW motor. - Electrical panel with SIEMENS PLC. - Integrated control panel. - Operating conditions of this item: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. Auction-ID: A7-48840-10

- Nominal force 400 T. - Maximum working pressure of the hydraulic system 25 MPa. - Dimensions of the work table approx. 2050 x 1600 mm. - Carriage stroke 1500 mm. - Maximum tool dimensions 2000 x 1300 x 600 mm. - Approach speed 500 mm/s. - Working speed 10-100 mm/s. - Return speed 500 mm/s. - Total installed power 52.50 kW. - Electrical control panel with regulation of process parameters. - Perimeter protection cabin with safety guards and interlocks. - Installation with access platforms for maintenance of the upper equipment. - Operating conditions of this item: unchecked. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. Auction-ID: A7-48840-3

Plate dimensions: 2.500 x 1.1250 mmDaylight opening: 300 mmNumber of daylights: 1 St.Heating: Specific pressure: kg/cm²Total pressure: toMotor output: kWDimensions (L/W/H): mmweight of the machine ca.: ca. 3 t kgYear: unbekannt Year: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 2920x980x1450 mmWeight: 1500 kgTotal power requirement: 11,5 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 1400x2450x2800 mmTotal pressure: 400 toweight of the machine ca.: 12000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 2950x1550x2950 mmWeight: 4000 kgTotal power requirement: 1,6 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 2960x1500x2000 mmWeight: 4000 kgTotal power requirement: 19,5 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3940x1620x2130 mmWeight: 5760 kgTotal power requirement: 32,5 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.