161 ENGEL used machine for sale

Key data: 4000 kN, 763 g/PS, 60 mm

Year of Make: 2000 Clamping force: 400 tons. Shot volume: 848 cm³ Screw diameter 60 mm Injection pressure increased: 2,421 bar Good condition, immediately available

Engel Screw Barrel Bimetal, new and unused 105 mm diameter LD 22 4550 Unit: 3380 cm3 5550 Unit: 3700 cm3

Ref. no.: 18092 Hersteller: ENGEL Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg

injection molding machine Angel Type: Victory 330/80 Tech Machine No: 155871 Age : 2005

Injection moulding machine Engel victory 200H/200V790 comb BJ 2018

Injection moulding machine Engel e-motion 2440/380 T BJ 2008

Key data: 800 kN, 239 g/PS, 45 mm

The machine is in good condition and has been maintained during operation at short maintenance intervals. The machine is connected and fully functional. A visit with a test is possible. All documents for the machine are available. The screw, heating cylinder tube and RSP were renewed in 2022 by Plasma Kunststofftechnik. Baseline: - No: 21953 - Year of construction: 1991 - Weight: 4000kg. - Clamping force: 800kn - Dimensions: 3910mm x 1380mm x 2050mm (LxWxH) - Control:CC100 Technical details: - Operating voltage: 400V 3~50Hz - Worm: 45mm - Screw geometry: 3-zones - Dosing distance max.: 160mm - Nozzle thread: M28x1.5 - Max. spray pressure: 1300 bar - Injection weight PS: 239g - Horizontal spar spacing: 405mm - Vertical spar spacing: 345mm - Opening travel max.: 430mm - Installation height min: 150mm - Installation height max.: 430mm - Centering: 125mm - Cooling  ...

Ref. no.: 18255 Hersteller: ENGEL Year of construction: 2004 Clamping unit Clamping force: 180 ton Opening stroke: 750 mm Distance between tie bars: 960 x830 mm Mould height min.: 500 mm Opening width: 1250 mm Injection unit Screw diameter: 45 mm Injection volume: 318 cm³ Shot weight: 302 g Injection pressure: 1769/2360 bar Measurements and weight Machine weight: 13500 kg Robot Producer: Wittman Type: W743 Year: 2009

Key data: 2000 kN, 562 g/PS, 55 mm

Specification Injection Moulding Machine Engel VC 1350/200 Tech General data Clamping force: 200 t Year of Make: 2007 Injection unit weight: 562 g Injection Unit .../1350 Screw diameter: 55 mm Specific injection pressure: 2183 bar Injection volume: 618 cm³ Injection unit weight: 562 g Tool clamping unit 200/... Clamping force: 200 t Dimensions of the tool plates: 860 x 570 mm Output force: 80 kN Tool height: 400 mm Opening travel: 750 mm Maximum panel spacing: 1150 mm Discharge stroke: 180 mm Other Specifications Weight: 14200 kg Dimensions (L x W x H): 6.3 x 1.9 x 2.3 m Year of Make: 2007 Equipment 2 x hydraulic core on the moving plate Pneumatic valve Integrated robot 8 zones for hot runners Rotameter 8-fold

A two-component injection moulding machine Engel with piggyback configuration, including Engel Viper 40 robot and safety enclosure, is available. Clamping force: 1800kN, nozzle diameter: 35mm, min. mould installation height: 270mm, max. platen distance: 1020mm, tie bar spacing: 980mm, centering: 180mm. Screw diameter 1/2: 22mm/15mm, injection pressure 1/2: 2392bar/2203bar, injection weight 1/2: 66g/19.5g. Robot year of manufacture: 2014, robot travel X/Y/Z: 700mm/1300mm/2360mm. Machine dimensions X/Y: approx. 6700mm/2100mm, control: CC400, operating hours: approx. 38567h. The 22mm screw needs to be replaced. Without conveyor belt. Documentation available. An on-site inspection is possible.

A total of four Engel injection molding machines are available. 1) Engel ES 80/25 HL-V, year of manufacture: 1999, the machine is a defective spare parts carrier. 2) Engel ES 80/25 HL-V, year of manufacture: 2001. 3) Engel VC 200/45 Tech, year of manufacture: 2004. 4) Engel e-Motion 200/55, year of manufacture: 2005. Documentation available. On-site inspection is possible. Individual sale possible.

Key data: 280 kN, 30 mm

Injection moulding machine ENGEL Victory 200-28 Tech Stock No.: 503562 Manufacturer: ENGEL Type: Victory 200-28 Tech Hours: 31150 Control: CC200 Year of Make: 2011 Technical data closing page Clamping force: 280 kN Panel size h x v: 500 x 450 mm Min. installation height: 150 mm Plate spacing max.: 550 mm Opening travel: 400 mm Ejector stroke: 100 mm Ejector force: 40 kN Centering of movable plate D: 125 mm Centering of fixed plate D: 125 mm Tool weight: 450 kg Technical Data Spray Side Screw diameter: 30 mm Displacement: 135 cc Spray pressure: 1065 bar Screw length: 17 l/d Screw stroke: 140 mm Screw speed: 480 min Injection flow to the outside: 78 g/s hp Number of heating zones: 4 Nozzle travel: 230 mm Dimensions & Weight Machine dimensions LxWxH: 3.2m x 1.35m x 1.85m Total Weight: 2900KG Equipment Screen text German Levelling elements Technic ...

Key data: 1200 mm, 141 , 35

Screw diameter: 35 mm Stroke volume: 154 cm³ Injection weight in polystyrene: 141 g/hp Injection pressure: 2,177 bar Clamping force: 120 t tie-barless Tool installation height min.: 300 mm Opening distance: 500 mm CONTROL: CC200 Screen text: german / german Operating instructions: german / german incl. ERC 23/1-F robot, with integrated storage belt Pump drive power: 15kW Total connected load: 24.2 kW Total weight: 7,300 kg Dimensions L x W x H: 4.4 x 1.5 (+0.8) x 2.0 m m m m Payment terms: 100 % before taking over the machine, net only

Key data: 450 mm, 63 , 25

Screw diameter: 25 mm Displacement: 69 cm³ Injection weight in polystyrene: 63 g/hp Injection pressure: 2,400 bar Clamping force: 45 t tie-barless Tool installation height min.: 175 mm Opening distance: 355 mm CONTROL: CC200 Screen text: german / german Instruction manual: german / german Sprue picker er/usp Pump drive power: 11 kW Total connected load: 17.8 kW Total weight: 3,300 kg Dimensions L x W x H: 3.3 x 1.2 x 2.0 m m m Payment terms: 100% before taking over the machine, net only

clamping force: 4.000 kN injection volume: 2.700 cm³ screw diameter: -- mm platen size: -- mm Condition: used, Specification: Rubber Injection Molding Machine - second-hand clamping unit: - Clamping force: 4000 kN - ejection device: 2-layer - Brush system: 2-layer Injection unit: - Injection volume max.: 2,700 cm³ Two identical systems are available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 750 kN, 35 mm

Engel - Injection moulding machine e - Max - 310/75 ( No.:4 ) -Electric - Year of construction: 2009 - With special accessories: Crane: 1000 kg - Screw: 35 – diameter - Actual shot value: 42,349,940 pcs. - Operating hours: 100,778 h – In automatic: 67,929 h - Control: LC-200 - Screen: 15 – inches - Clamping force: 750 KN - Mold plate size: 560 mm x 600 mm - Weight: 4,400 kg - Sales from location: Germany

Key data: 750 kN, 35 mm

Engel - Injection moulding machine e - Max - 310/75 ( No.:3 ) -Electric - Year of construction: 2009 - With special accessories: Crane: 1000 kg - Screw: 35 – diameter - Actual shot value: 41,658,321 pcs. - Operating hours: 103,302 h – In automatic: 65,611 h - Control: LC-200 - Screen: 15 – inches - Clamping force: 750 KN - Mold plate size: 560 mm x 600 mm - Weight: 4,400 kg - Sales from location: Germany

Key data: 750 kN, 35 mm

Engel - Injection moulding machine e - Max - 310/75 ( No.:2 ) -Electric - Year of construction: 2009 - With special accessories: Crane: 1000 kg - Screw: 35 – diameter - Actual shot value: 34,527,644 pcs. - Operating hours: 98,349 h – In automatic: 54612 h - Control: LC-200 - Screen: 15 – inches - Clamping force: 750 KN - Mold plate size: 560 mm x 600 mm - Weight: 4,400 kg - Sales from location: Germany

Key data: 750 kN, 40 mm

Engel - Injection Molding Machine e - Max - 310/75 ( No.:1 ) -Electric - Year of construction: 2009 - With special accessories: Crane: 1000 kg - Screw: 40 – diameter - Actual shot value: 40,069,660 pcs. - Operating hours: 105,347 h – In automatic: 63,211 h - Control: LC-200 - Screen: 15 – inches - Clamping force: 750 KN - Mold plate size: 560 mm x 600 mm - Weight: 4,400 kg - Sales from location: Germany

Key data: 700 kN, 35 mm

used injection moulding machines ENGEL VICTORY 200-70 Tech Stock No.: 503473 Manufacturer: ENGEL Type: VICTORY 200-70 Tech Control: CC100 Year of Make: 2004 Hours: 77192 h Technical data closing page Clamping force: 700 kN Panel size h x v: 670 x 420 mm Min. installation height: 150 mm Plate spacing max.: 600 mm Opening travel: 450 mm Ejector stroke: 100 mm Ejector force: 40 kN Centering of movable plate D: 125 mm Centering of fixed plate D: 125 mm Tool weight: 675 kg Technical Data Spray Side Screw diameter: 35 mm Displacement: 154 cc Spray pressure: 1600 bar Screw length: 20 l/d Screw speed: 400 min Plasticizing current: 21 g/s PS Outdoor injection flow: 151 g/s hp Number of heating zones: 4 Nozzle travel: 250 mm Dimensions & Weight Machine dimensions LxWxH: 4.4m x 1.5m x 2m Total Weight: 5200KG Equipment Screen text German Screentext English  ...

Förderbaänder 16 A 380 V Slow runners Length 90 cm Width 15 cm Height 15 cm

clamping force: 450 kN injection volume: 135 cm³ screw diameter: 35 mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPE - used clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 1.750 kN injection volume: 318 cm³ screw diameter: 45 mm platen size: 700 x 700 mm daylight between platens - max.: 460 mm Condition: used, Specification: Horizontal injection moulding machine, Injection unit: - Screw diameter: 45 mm - Screw length L/D: 20 - Spray volume: 318 cm³ - Shot weight max.: 287 g - Special spraying pressure: 2,100 bar Clamping unit: - Max. clamping force: 1,750 kN - clamping plates: 700 x 700 mm - Opening path max.: 460 mm - mould installation height: 150 mm - Operating hours: 89217 h - 1x core puller - Handling / Robots: ENGEL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Screw cylinder complete with screw, cylinder head and closure nozzle for ENGEL injection unit size ES3550

Hydro motor for screw cylinders Injection unit size ES3550 Hägglunds Drives type CA50 20 2 0 0 N 004

PET Preform injection moulding machine Clamping force 320t Spray weight 6935gr. Snail 130mm Preform extraction system SERVO IV, TPS robot TRT-M4-72-E, 72-speed, 4-stage, incl. withdrawal kit, conveyor belt LT/h 1825, dosing Motan Minicolor PET

Complete control CC 90 for ENGEL injection moulding machines

Hydraulic injection moulding machine manufactured in 2021. This Engel Victory 320/80 spex features a clamping force of 800 kN and an opening stroke of 450 mm. The machine has a maximum daylight of 750 mm and a mould height minimum of 300 mm. If you are looking to get high-quality injection moulding capabilities, consider the Engel Victory 320/80 spex machine we have for sale. Contact us for further details.

Clamping Force: 420 ton // Shot Weight (Max): 1555 g

- RC200 integrated - drive package multidynamic - 1 x switchable vacuum/pneumatic circuit - 1 x compressed air circuit - electric supply network: 3x380V+N+PE/60HZ - compact electric cabinet mounted on Z-axis - incl. 4DI /4DO free programmable - han