peripheral equipment (e.g. heating, conveying, drying) used for sale (598)

Press cooling star discharge for material handling of pressed door elements

Screw compressor CompAir Type L07-13 Year of manufacture 2008 CE With compressed air dryer Make Knoll EKO MAK Power 7.5 kW Volume flow 0.69 m³/min. Step pressures 13 bar Suction pressure 1.0 bar Full assist current 15/18 amps Speed 3000 rpm. Voltage 400 Volt / 3 Phase / 50 Hz

Höcker Polytechnik extraction system Year of manufacture: 8/2000 CE 3 chip collection barrels Fan Type SV 25/220 Motor 5.5 kW Volume flow 3890 m³/h Pressure increase 2500 Pa Motor vibration 0.18 kW Rotary valve 0.37 kW PLC control Emergency stop shutdown Level monitor very good condition because little used

Used Höcker Dreisack 180 Socks with Feet Without blower

Used hot air generator with oil burner Ready for operation at the site

380 V, 50 Hz, 2.2 Kw Volume flow 2230 m³/h Suction nozzle 160 mm Pt 2180 Pa

Specifications: • Housing made of galvanized sheet steel, the individual elements are screwed • Sound insulation with perforated sheet metal in front is installed on the inside of the back • The separation of the paint mist from the exhaust air c takes place via approved folding cardboard filters with glass fibre filters in the 2nd filter stage (99 % separation efficiency depending on the coating system) • The high-performance filters inserted in the front have a paint storage capacity 3 – 5 times greater than glass fibre mats and can be easily removed and disposed of when changing the filter • Diameter exhaust air pipe: 500 mm • Extraction capacity: 7200 m³/h • Motor power: 1.5 kW ex • Noise level: approx. 78 dB(A) with standard motor installation on the extraction system • External dimensions: 2,500 x 2,000 x 750 mm (W x H x D), height with fan: 2,700 mm ...

Nestro Dust Collector NE 250J ECO Nominal volume flow 2,950m³/h Nominal Volume Flow Vacuum 2.526Pa 5.5Kw Filter area: 22.4m² Outrigger: 250mm

11 KW

2.55 KW

4.3 KW 2850 rpm 4240 m3/ min

4.3 KW 2850 rpm 2440 m3/ min

6.69 KW 3000 rpm 73 m3/ min

liter capacity: 120 lfeed pressure: 218 barcoolant capacity: - lelectrics - voltage/frequency: 380 / 50 V/Hzfilter pump: 150 kWtotal power requirement: 14 kVAweight of the machine ca.: 1,5 tAF-Automatic pre-coat filterwith return-flow cooling of gthe grinding oil and the hydraulicfluidThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Vnenn: 2,950 cbm/h Vmin: 2.251 cbm/h Suction nozzle Ø 200 mm Motor power 3.7 kW Rated speed 2,805 rpm Rated current 7.5 A Frequency 50 Hz, 3 phases Test class H2 Vacuum at Vmin at the interface between dust collector and dust generator (4 m hose) with suction nozzle Ø 200 mm = 2,200 Pascal = 22, with suction nozzle Ø 180 mm = 2,500 Pascal = 25 Filter cleaning by compressed air (to be triggered manually, compressed air connection on site, max. 4 bar) Delivery incl. various chip collection bags

Centrifugal fan / blower / fan Hürner-Funken made of chemical-resistant plastic The housing and impeller of the fan are made of chemical-resistant plastic and suitable for aggressive media in the process exhaust air. Manufacturer Hürner-Funken GmbH 35325 Mücke-Atzenhain Type 16-RU 315 MN/0/1420 Factory No. 2-29191/00 Built in 1999 Air capacity / volume flow 2166 / 1900 m³/h Motor power 1.50 KW, 1619/1420 rpm. Pressure difference 1287/990 Pa Conrad Meisenheim electric motor Type DR 90 L-4 No. 304987 1.5 KW, 400/230 V star/delta, 3.4/6 A, 50 Hz Iso F, IP55 1420 rpm, cos phi 0.82 Chemically resistant, corrosion resistant. The centrifugal fans made of plastic are specially designed for pumping chemically aggressive exhaust air. They are characterized by the highest corrosion resistance. In addition, they achieve high volume flows and Pressure differences wit ...

Finnrose Plate Stacker Type ST-10-170 Electronic For automatic stacking (e.g. on roller conveyor for further transport) Of plate-shaped workpieces, doors, or woods Was used to stack timber behind a four-sided planer Workpiece size Maximum 2500 mm x 800 mm Minimum 400 mm x 250 mm Weight maximum per workpiece 80 kg Capacity 20 workpieces per minute, depending on the workpiece size Maximum stacking height above floor 1800 mm Belt drive 0.18 kW Roller drive 0.09 kW Compressed air consumption per stroke 3.9 NL Instruction manual and circuit diagram available Weight approx. 600 kg Dimensions 2800 mm x 2200 mm x H 1100 mm (H max. 1800 mm)

Key data: 42 m²

Extraction system Filter system Spänex Model ADDITOR U Type II + III – VU – 15 – SBU 165 – S2 – 000 Order number 40132/93 Built in 1993 Filter area 42 m² Filter bag material needle felt, in very good condition Capacity 64,200 m³/h 5 chip collection containers each 165 litres Motor vibration With heat return air duct Fire Extinguishing Line With control cabinet With documentation and circuit diagram With fan 7.5 kW Pipe connection diameter on the fan 300 mm Dimensions of the extraction system Frame with container Overall height 2971 mm Overall width 980 mm Length of the extraction system approx. 3600 mm Plus add-on parts The plant has already been dismantled and Ready for loading from stock

table length: 1300 mmtable width: 800 mmstroke height: 1010 mmweight max. in kg: 2000 kg: 190 mmconnected load frequency: 400 Vtotal power requirement: 0,75 kWstroke speed - idle stroke upwards: 40 sek.stroke speed - idle stroke downwards: 30 sek.weight of the machine ca.: 0,28 tdimensions of the machine ca.: 1,3 x 0,8 x 0,23 mThe hydraulic lifting tables are electrically driven and operated.Have a contact strip for safe lowering operation.Wide applicability for workshops, assembly departments, loading pits, etc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2200 mmtable width: 1500 mmstroke height: 1900 mmweight max. in kg: 3000 kgtotal power requirement: 1,5 kWstroke speed - idle stroke upwards: 55 sek.stroke speed - idle stroke downwards: 30 sek.connected load frequency: 400 Vweight of the machine ca.: 0,650 tdimensions of the machine ca.: 2,2 x 1,5 x 0,3 mThe hydraulic lifting tables are electrically driven and operated.Have a contact strip for safe lowering operation.Wide applicability for workshops, assembly departments, loading pits, etc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.