4 WEINBRENNER bending presses used machines

Working width: 4100 mm sheet thickness: 16 mm projection: 300 mm rear gauge: 1500 mm power: 400 V, 45 kW space: 4800 x 3500 x 2600 mm weight: 28000 kg

Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h

Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration  ...

pressure: 200 t chamfer lenght: 3050 mm distance between columns: 2550 mm Control: CYBELEC VisiTouch Pac stroke of ram: 524 mm weight of the machine ca.: 17.000 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t chamfer lenght: 2050 mm distance between columns: 1550 mm throat: 250 mm stroke: 200 mm adjustment of press crosshead: 200 mm stroke speed - idle stroke downwards: 105 mm/sec stroke speed - idle stroke upwards: 180 mm/sec stroke speed - under load: 9,5 mm/sec table width: 200 mm table height over floor: 900 mm dayligth: 280 - 480 mm back stop - adjustable: 3 - 729 mm control: CYBELEC SYNCHRO control: CNC 7400 PS total power requirement: 7,5 kW weight of the machine ca.: 10 t dimensions of machine L x W x H: 3,70 x 2,45 x 2,80 m Accessories: programmable back gauge, table extensions, various upper and lower dies segments The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4050 mm plate thickness: 20 mm distance between columns: 4100 mm column daylight: 4200 mm no. of strokes: 10-20 Hub/min working pressure: 250 bar total power requirement: 85 kW weight of the machine ca.: 43,6 t dimensions of the machine ca.: 5,5x2,8x2,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Working width: 3050mm, material thickness: 6mm, throat depth: 200mm, back gauge adjustment: 1000mm, drive power: 15kW, cutting angle range: 1°-2°, table height: 900mm. Machine dimensions X/Y/Z: approx. 4100mm/2300mm/2100mm, weight: approx. 8500kg. On-site inspection is possible.

Pressing force: 3200kN, enlarged stroke: 810mm, working width: 4050mm, ram speed: downwards: 130mm/s, pressing: 6.5mm/s, upwards: 75mm, stop time: 109ms, safety distance: 174mm, weight: approx. 29000kg, operating hours: 16010h, control: Cybelec ModEva 15S. Including 4 bending aids and angle measuring sensor. Dies, embossing tools, pointed punches, roe foot punches, closing bar, extension for upper tool, radius tool and adapter available on request. Documentation available.

pressure: 200 t chamfer lenght: 3050 mm distance between columns: 2550 mm stroke of ram: 274 mm control: Cybelec ModEva Pac total power requirement: kW weight of the machine ca.: 17.000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 80.0 t chamfer lenght: 2050 mm distance between columns: 1550 mm column arm: 250 mm table width: 85.0 / 135 mm stroke: ca. 390 mm dayligth: ca. 585 mm ajustment speed: 180 mm/sec working feed: 1.0 - 10.0 mm/sec return speed: 135 mm/sec work height max.: 1050 mm Number of working hours: 32.495 h oil volume: 200 l operating pressure: 320 bar total power requirement: 11.6 KW weight of the machine ca.: 7300 kg range L-W-H: 3700 x 2000 x 3000 mm ** Good/well-maintained condition (!!) - in checked conditions - machinevideo - https://www.youtube.com/watch?v=IKyUmzB0WTI ------------------------------------------------- CNC electro-hydraulic press brake with: * Increased installation height .. approx. 550 mm * Increased cylinder stroke .. approx. 390 mm ------------------------------------------------- Features: - Robust electro-hydraulic press brake * MADE IN GERMANY (!!) - CYBELEC CNC ...

pressure: 200 t chamfer lenght: 3600 mm distance between columns: 2650 mm dayligth: 500 mm throat: 300 mm stroke: 250 mm working feed: 10,5 mm/sec return speed: 100 mm/sec ram stroke speed: 150 mm/sec table height: 900 mm oil volume: 500 l total power requirement: 37 kW weight of the machine ca.: 17800 kg dimensions of the machine ca.: 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

* General * SKU332X713 * LocationBarneveld * MakeIgefa Weinbrenner * Type061U-600-600 * No.50467 * Year of construction2014 * Pressure * Vacuum possiblecheck * Vacuum possible jacketcheck * Working pressure shell10 Bar * Vacuum possible shellcheck * Working pressure tubes10 Bar * Tubular vacuum possiblecheck * Main Features * Shell (Material)Stainless steel * Tube (Material)Stainless steel * Surface41 m2 * Specified Features - Shell and tube heat exchanger * MaterialStainless steel 1.4571 (316Ti) * Heat exchangercheck * Horizontalcheck * Heating surface41m² * Tube capacity582 l. * Number of tubes:178 * Tube diameter33,7 mm * Tube length2200 mm * Wall thickness tubes2 * Max. temperature0°C/+200°C * Shell capacity252 l. * Shell diameter600 * Shell length2500 * Max. temperature0°C/+200°C * Shell connectionsDN80 * Cover connectionsDN500 * Information * Mounted on framecheck * Total heig ...

pressure: 250 t chamfer lenght: 3550 mm distance between columns: 3000 mm Control: Cybelelc DNC 1200 total power requirement: kW weight of the machine ca.: 18.500 kg dimensions of the machine ca.: 4300x2750x3750 mm Accessories: - 2-hand foot switch - Lasersafe Fisseler - Hydraulic tool clamping at top and bottom - Die shift - Hydraulic crowning - Support arms - Cybelec DNC 1200 control - 1 set of upper and lower tools - Controlled axes y1, y2, x, r, z1, z2, inclined stop - Protective grille The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Type of press: 2-cylinder synchronized press, pressing force: 125t, rated pressing force: 110t, bending length: 3000mm, ram stroke: 360mm, installation height: 540mm, distance between frames: 2550mm, hydraulic pressure: 256bar, weight: approx. 12000kg, control system: Cybelec DNC 7000 Graphic. Including various tools. The control system and the screen were renewed in mid/late 2025. An on-site inspection is possible.

Scissors

Hand guillotine shears, guillotine shears, sheet metal shears, sheet metal shears, folding machine, edging bench -Hand guillotine shears combined with: folding machine -Cutting width: 610 mm -Max. Section thickness: 1.0 mm -Swivel bending machine -Max. Working width: 610 mm -Max. Sheet thickness: 1.0 mm -Transport dimensions: 845/910/H1230 mm -Weight: 240 kg

Hand guillotine shears, guillotine shears, sheet metal shears, sheet metal shears, folding machine, edging bench -Hand guillotine shears combined with: folding machine -Cutting width: 610 mm -Max. Section thickness: 1.0 mm -Swivel bending machine -Max. Working width: 610 mm -Max. Sheet thickness: 1.0 mm -Transport dimensions: 845/910/H1230 mm -Weight: 240 kg

Semi-automatic bending, pipe bending machine, mandrel bending machine MOBITEC type BAH 1-2KOTTMANN and BERGER GmbHFabr. No. 056 Year of construction 09/2004- for simultaneous bending of two pipe sections made of steel up to 12 mmBending angle max. 90Pipe diameter max. 12mmMandrel length approx. 65 mmNominal power 3.5 kWDreturn air max. 6 bar / approx. 1 litre per bending cycleMains connection 400 volts, 50 Hz- Pneumatic clamping- Pneumatic mandrel retraction- Control for angle input via STOBER Controlbox Series 4000/5000- Control SIEMENS

Folding machine KRAMER type A-toll. II 1000Fabr. No. 48 287 Year of construction 1990Useful length 1060 mmmax. Sheet thickness 3.75 mmStroke of the upper beam 180 mmAdjustability of the bending beam 60 mmBack gauge 480 mmDrive power of bending beam drive 4 kWAdrive power of upper beam drive 1.5 kWNet connection 400 volts, 50 Hz- manual and semi-automatic control- angle adjustment via angle selector- one-piece pointed rail 135- back gauge with hand crank adjustment and simple measurement scale-

Bending tool, die, lower knife, lower tool, lower jaw -Tool: for swivel bending machine -Widthen: for lower cheek -Dimensions: 59 x 19 mm -Length: 1452 mm -Weight: 10 kg

Bending tool, die, lower knife, lower tool, lower jaw -Tool: for swivel bending machine -Widthen: for lower cheek -Dimensions: 59 x 19 mm -Length: 1452 mm -Weight: 10 kg

Tube bending machine - mandrel bending machine TRACTO-TECHNIK Type Transfluid DB 2060 KSerien. No. 70173 Year of construction 2004Bending capacity (steel) max. 76.1 x 3.0 mmBending capacity (stainless steel) max. 76.1 x 1.65 mmBending tool max. 70 x 2 mm (for stainless steel)Pipe slide length 4572 mm (4300mm)Bending radius max. 150 mmBending direction clockwise (right)Bending angle max. 190Bending head speed at 90 8 sec. Hydraulic operating pressure 200 barEngine power 3 KWnet connection 400 Volt, 50 Hz, 15

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5Hand swivel bending machine, bending benchYear of construction approx. 1985Working length 650 mmSheet thickness at 40 kg/mm2 1.5 mmUpper beam opening approx. 60 mmBending beam adjustment approx. 0-25 mmBending angle 0-180- Upper beam adjustment via hand crank- Pilot rail for the bending brace- One-piece sharp rail 135Space requirement L x W x H 1200 x 600 x 1100 mmWeight 160 kggood condition; used

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5Hand swivel bending machine, bending benchYear of construction approx. 1985Working length 650 mmSheet thickness at 40 kg/mm2 1.5 mmUpper beam opening approx. 60 mmBending beam adjustment approx. 0-25 mmBending angle 0-180- Upper beam adjustment via hand crank- Pilot rail for the bending brace- One-piece sharp rail 135Space requirement L x W x H 1200 x 600 x 1100 mmWeight 160 kggood condition; used

Hydr. Press brake, die bending machine HAMBURGER JONESCHEIT type HYPM 70-2600Fabr. No. 4004 Year of construction 1987Printing capacity 70 ton. Working length 2600 mmStand width 2770 mmPlunger stroke 60 mmDistance table - ram max. 390 mmTable size 2750 x 200 mmMotor power 7.5 kWWet connection 380 volts, 50 Hz.- Crimping depth via mechanical fixed stop with electric adjustment and mechanical depth indicator- Lower tool consisting of 2 segments, each 835 mm, with 2 different prisms (15 and 24 mm)- Upper tool,