5 PAAL conveying belts used machines

used chain conveyor belt Manufacturer: PAAL Type: KEL 1000 Year of construction: 1997 specifications: Conveying width: approx. 1,000 mm Center distance:approx. 7,500 mm Band course: ascending over the entire length, Conveyor belt drive power: 3.0 kW Side bolster height: 500 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers,  ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...

automatic baling press Manufacturer: PAAL Type: KONTI 275 F Built: 2007 Main parts of the press: 1 automatic duct press (without wire winding devices) 1 automatic lacing 1 Hydraulic system 1 Electric control technical data: Pressing force: 800 kN / 80 t at 300 bar Specific pressing force: 9.70 kg/cm2 Channel cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,600mm Number of connecting wires: 4 pieces vertically Drive power: Main pump: 1 x 45 kW Pump delivery capacity: 1 x 380 l/min Throughput: up to approx. 280 m3/h under operating conditions Performance at: - 35 kg/m3 bulk weight: approx. 9.5 t/h - 60 kg/m3 bulk weight: approx. 16.5 t/h - 100 kg/m3 bulk weight: approx. 26.0 t/h Hydraulic oil tank volume: 2,100 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other equipment: Operator Panel MP 270 auto ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 2007 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 155 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press.  ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1996 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 162 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press. T ...

automatic baler Manufacturer: PAAL Type: KONTI 275 D/k Year of construction 1999 specifications: Pressing force: 75 t Specific pressing force: 9.09 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 500 - 750 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 75 kW Throughput: 350 m³/h Pressing capacity: - approx. 12.0 t/h at department store (35 kg/m³ bulk density) - approx. 21.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 33.0 t/h for collected goods (100 kg/m³ bulk density) Binding: 4-fold vertical + 3-fold horizontal Machine weight: approx. 25.0 t

automatic baler Manufacturer: PAAL Type: PACOMAT IS Year of construction: 1988 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Channel size: 700 x 700 mm Opening: 800 x 650 mm Drive power: 22 kW Throughput: 100 m³/h with additional manual hopper Wire flow in the pressing direction seen on the left side

automatic baler Manufacturer: PAAL Type PACOMAT II S SO Year of construction: 1994 specifications: Pressing force: 50 t Specific pressing force: 7.14 kg/cm² Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm Drive power: 45 kW Throughput: approx. 170 m³/h automatic 4-fold horizontal binding

An original control cabinet that was dismantled by PAAL Konti 125D, built in 1999. It is based on SIEMENS S5 controller. A complete control cabinet, functional

Control cabinet for PAAL accounts 200, 275, 325, 425, 500, 600, 700 after renovation An original control cabinet, the one from the PAAL Konti 425 B/K, built in 1992, with the cross binding. It is based on SIEMENS S5 controller. It is also suitable for the other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power, also for the variant with the cross binding. A complete control cabinet, functional, after renovation We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet that was dismantled by PAAL Konti 275 C, built in 1994. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325,425, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet dismantled by PAAL Konti 200B, built in 1987. It is based on analog relays. It is also suitable for the other models such as: Konti 125, 200, 275 , depending on model and drive power. A complete control cabinet, functional

An original control cabinet that was dismantled by PAAL Konti 425 B, built in 1991. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet that was dismantled by PAAL Konti 425 B, built in 1991. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet that was dismantled by the PAAL Konti 600 E/K, built in 2005. It is based on SIEMENS S7 controller. It is also suitable for other models such as: Konti 700 A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

used box press Manufacturer: PAAL Type: HS 34 specifications: Filling box size: 1,000 x 700 x 2,200 mm (W x D x L) Filling opening: - 1st filling: 2,200 x 1,000 mm - 2nd filling: 1,200 x 1,000 mm Press pressure: approx. 18 t Drive power: 4 kW Lifting speed pre-pressing and retraction: 2.5 m/min. Lifting speed repressing: 1.25 m/min. Bale size: approx. 700 x 1,000 x 1,300 mm Bale weight: up to approx. 300 kg Weight of the machine: approx. 2000 kg Machine dimensions: 3,500 x 1950 x 1,450 mm (L x W x H)

automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side

New hydraulic pump QX61-250/63-100R88 for PAAL channel baler. Can be used in systems with a 75kW motor.

Brand new gear pump, with internal gearing for PAAL Konti, Pacomat channel baling press. Can be used in systems with a motor of at least 22 kW

Dual hydraulic pump for PAAL, 45kW Used 2-piece hydraulic pump for PAAL channel baling press. Can be used in systems with a 45 kW motor

Used Triple Hydraulic Pump QX51-125/53-063/52-063R91 for PAAL channel baler. Can be used in systems with a 45 kW or 55 kW motor. Manufacturer partnumber: QX51-125/53-063/52-063R91

Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic