43 MATEC used machine for sale

Vibrorinne MATEC drive rear Overtime separation and â repatriation Vibro Drive 1 electric motor 3 kW Linder nominal width inside 500 mm Preparing for 1700 mm Linen nominal length 4000 mm Peasant sheet seal unit perforation 20 mm Weight about 560 kg Built in 2018, new The machine is in very good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Vibrorinne MATEC vibrating mesh drive 4 4 kW, 3 x 400 V 50 Hz Pan nominal width 600 mm Gutter inner width 500 mm Trough depth 260 mm Extra deep OK built channel 480 mm Gutter length approx. 11'000 mm Transport speed nominal approx. 17 m / min Year 2018 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

MATEC Stappler tipping bucket type 2 The tipping bucket can be locked with a bolt with cotter pin so no tipping is possible. The tipping buckets can be supplied also with a hydraulic tilting device. The blades are 1950 mm wide and type 2 1300 mm deep. The standard blade height is 450 mm. Solid wall or lattice towers can be ordered as accessories. The nominal weight of the shovel is 2000 kg. Each blade has 4 lifting eyes for crane handling. 4 mm thickness, corners and a replaceable wear bar reinforced permit prospecting. Other blade dimensions are possible upon request. Year 2017 New machine Spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfelden Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041  ...

Wood chopper f. tractor PTO wood chipper ECOSTAR 8 as a kit for the self-Assembly (image mounted with other rotating device) - feeder height width 20/20 cm - upper feed roller with belt drive - disk hacker with 2 knives and 1 counter knife - rated about 5 cubic metres chip length nominal 15 mm - CE compliant - PTO - rotating ejector - delivered in metal crates -Warranty: 2 years on all non - consumable - options for an additional fee: - machine Assembly by supplier - pulverizing integrated to avoid excess - special execution for the manufacture of Pelletschnitzeln with 6 mm length - professional Rotary chute which together does not rust and freezes at Sub-zero temperatures, with lever - built diesel drive 35 HP - electric motor 15 kW model changes built up which are not exactly the figurative representation are reserved! Spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfe ...

The ECOSTAR 8 slices hacker with diesel drive 35 HP, 3 cyl., with an increased swivel discharge for horticulture, wine fruit, forestry, agriculture, etc. at a cheap price. With 2 blades, disk diameter 605 mm, disc speed 1200 rpm, JD diesel engine 3100, 3 cyl, 35 HP, water-cooled, feed height 200 mm, max wood diameter 200 mm, Einzugbreit 225 mm, hopper opening 600/600 mm, output per hour 5-8 cubic metres. The machine is ready for use within 1 minute. The chips can easily be abandoned on the bridge of the towing vehicle. The tedious tying of the branches fall away. Take the chips only 1 time in the hands. Watch the video movie in matnews91 on YouTube: ECOSTAR diesel JD3100 8. Price does not include trailer euro 9' 390.00 Expressly subject to technical changes, prior sale and error! Shipping costs CH / DE trucked approximately euro 280.00 MATEC systems + technology GmbH K ...

The MATEC HMS-350 Kleinshredder for professionals, with hammer mill is suitable for crushing of green waste, etc. All types of green waste such as bouquets, garden waste, potted plants, compost in each State, agricultural waste, Earth, cemetery waste, large wood chips and small wood waste, etc. can thus be crushed. The hammer mill is equipped with impact tools made of HARDOX, the appropriate anvil blow bar and the following "data" also made of HARDOX. The content of flower pots, flower boxes, "baked together" grass cutting, etc. can thus be crushed. The combination of anvil blow bar before calibration and subsequent anvil calculation for fine crushing results a high throughput capacity with a small expenditure of energy. Electric motor 7.5 kW, a diesel engine can 3x400V, 50 Hz, power outlet connection euro 32 A request be built up 350 mm diameter insertion slot flight circle diame ...

MATEC easily from our own development and production running lightly and quietly and transport bulk material and individual loads up to 250 kg with minimal energy over long distances up to 12 m at a time with a hand drill 300 w power consumption. The combined forced - and promotion of resonance stores the kinetic energy in the spring and must compensate for only the frictional resistance of the material. Sawdust, shavings, gravel, Earth, grain, hay and grass, etc. are exactly same speed transported with approximately 17 m / min. by means of Frequenzumforner the speed can be adjusted. The transport and screening in a single operation with a built-in sieve base perforation on request MATEC Vibrorinne standard Trough width inner 500 mm Trough height inner 260 mm current trough length 2500 mm (can front and rear to 1.5 m be extended without additional support) In addition current ...

MATEC forklift blades are robust and easy to build and can be attached to almost any commercial lyklift. With a fuse bolt, the tilting device can be blocked for special inserts. The front shutter flap can be mounted on any shovel. The interchangeable scraper is suitable for planing work such as removing ice, repelling soil, gravel or feed, etc. - Bucket width 1950 mm - Bucket depth type 1: 1000 mm, shovel depth type 2: 1330 mm - Bucket height without attachment 450 mm - Weight approx. 220 kg - Payload 2000 kg - Steel sheet 4 mm industrial lypainted - Fork shoes axle distance 800 mm - Fork tine width max. 170 mm - Fork thickness max. 60 mm - 4 lifting eyelets for krange slopes - Tilting device for cable pull with lifter and spring reset, securing bolt Options at extra cost: - Type 2 shovel depth 1330 mm Total price € 1590.00 - Front shutter € 590.00 - hydr. Liftin ...

This 5-axis Matec 30-HV was manufactured in 2009, featuring a versatile universal machining center with a large X-axis travel of 3000 mm and a Y-axis of 600 mm. It includes a high-speed range up to 12,000 rpm, a tool magazine for 36 tools, and a high-pressure cooling system (70 bar). Ideal for complex 3D machining with its powered CNC rotary table and Heidenhain iTNC 530 control. Contact us for more information about this machine.

- NC Rotary table 1250 mm with 50 Rpm - Full C-Axis  360.000 with HIGH TORQ Drive - HSK-100 with 90 kW and 15.000 Rpm - 5 Axis simulteneous package - Last service in 2023 

- 1 Axis CNC Swivel head, infinitely variable - Axis drive with ball screw drive - Roller linear guides in all axes - Direct path measuring systems - Full work area encosure with roof - Chip conveyor - Coolant unit - Measuring probe Renishaw RMP60

MATEC 30 HV CNC machining center was built in 2001 in Germany by Matec Maschinenbau GmbH. The machine, designed for precision machining of oversized workpieces, is equipped with a number of reliable components with excellent specifications. This includes a tilting work head, a 24-position tool magazine and a chip extraction unit. All this is complemented by the intelligent BOSCH CNC control, in which advanced machining programmes are created in just a few steps. The MATEC CNC vertical machining center weighs approximately 15000 kg. Technical specifications of the MATEC 30 HV CNC milling machine - CNC controller: BOSCH TYP 3 OSA - feed in the X/Y/Z axis: 3000/600/800 mm - maximum spindle rotational speed: 9000 rpm - minimum spindle rotational speed: 20 rpm - spindle drive power: 16 kW - tilting work head - rotation angle of work head: ± 90° every 1° - 24-position tool magazi ...