0 GUILLIET four sided planing machines used machines

Key data: 4 , 220 , 120

Guiliet Profilier and Hobelautmat with Wepla heads Model: 220 KXR 220 Year built:1990 Condition: very good (used) MAX CROSS-SECTION 220 X 120 MM MIN CROSS-SECTION 30 X 6 MM ENTRANCE TABLE 2000 MM long. PLANING SHAFTS 40 MM Dressing shaft 5.5 kW right and left planing shaft combined 5,5kW Thickness planer shaft 5.5 kW WEIGHT APPROX. 1600 KG Cleaned, maintained and functionally tested. If necessary, we can gladly offer planing heads with continuous cutting edges.

Key data: 4 , 180 mm, 120 mm

Used machine Workpiece width 180mm Workpiece height 120mm 4 spindles: 1) Horizontal bottom 180mm 3.7kW 2) Vertical right 120mm 4kW 3) Vertical left 120mm 4kW 4) Horizontal top 180mm 5.5kW Diameter of spindles 30mm

Key data: 4 , 180 mm, 130 mm

Four-way planer Guilliet Type KXY Year of manufacture 1989 Planing width maximum 180 mm Planing height maximum 130 mm 4 planing shafts Knife length 186 mm and 136 mm Minimum planing 30 mm x 6 mm Dressing table length 2000 mm Feed speeds 6 and 12 m/min. Spindle diameter 30 mm Feed motor 0.55 kW Lower dressing shaft approx. 3.7 kW Right wave approx. 3.7 kW Left wave approx. 3.7 kW Above approx. 5.5 kW Height adjustment 0.18 kW Extraction connection diameter 160, 120 and 140 mm Including planer heads Dimensions 3200 mm x 1400 mm x height 1700 mm Weight 1200 kg The first picture shows identical machine in our warehouse

Number of boring spindles: 4 St. Working width: 220 mm Working height: 120 mm Length of the planing table: 2.000 mm Feed motor: 1,5 kW Feed speed: 4,5 - 27 m/min. total power requirement: 15,5 kw Dimensions (L/W/H): 3.700 x 1.500 x 1.300 mm weight of the machine ca.: 1.600 kg turning speeds: 6.000 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SPECIFICATIONS: Feed length: 1970 mm Machinable width: 230 mm Machinable height: 110 mm Spindles: Ø 40 mm Number of Spindles: 4 Shaft drive Installed power: 16 kW Voltage: 380 V Spindle configuration: I bottom: 3.7 kW II right: 5.5 kW III left: 5.5 kW IV: top: 5.5 kW

Number of boring spindles: 2 St. Working width: 180 mm Working height: 120 mm Length of the planing table: 2100 mm Feed motor: 3,7 kW Feed speed: m/min. total power requirement: kw Dimensions (L/W/H): mm weight of the machine ca.: kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of boring spindles: 4 St. Working width: 180 mm Working height: 120 mm Feed speed: ca. 10 m/min m/min. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

4-side Planer SCM P 75 Year of construction 1983 Masch. No. 045 8vsoczcl8 Planing width of 180 mm Planing height of 130 mm 4 spindle length 2500 mm Weight 1670 kg L x W x h: 310 x 120 x 180 cm The machine is in good condition, little used, ready for use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

MULTI MOULDERS machine with 7 shafts type SCM SUPERSET 23 PLUS . with SLIDE and RETURN PIECES type MAHROS RP/4 second hand machine CE mark : Yes volt. 380/50 - Composition (7 shafts , 7 independent engines): 1° shaft : lower horiz . motor power Hp 7,5 2° shaft : right vertical . motor power Hp 7,5 3° shaft: left vertical (automatic). motor power Hp 7,5 4° shaft : upper horiz. motor power Hp 10 5° shaft : upper horiz. motor power Hp 10 6° shaft : lower horiz. motor power Hp 7,5 7° shaft : universal 360° . motor power Hp 10 grove table inlet length mm. 2400 feed speed: from 5 to 35 mt./min max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 automatic lubrication system weight kgs. 4300

MULTI MOULDER machine type WEINIG PFA 17N second hand machine 6 spindles with tools - Composition : 1° shaft : surface planer . motor power Hp 5,5 2° shaft : spindle moulder . motor power Hp 4 3° shaft : spindle moulder . motor power Hp 5,5 4° shaft : spindle moulder . motor power Hp 5,5 5° shaft : thickness planer . motor power Hp 5,5 6° shaft : surface planer. motor power Hp 5,5 inlet length mm. 2000 feed speed: from 7,8 to 58,8 mt./min max. useful working width mm. 170 max. useful working height mm. 120 lubrication system weight kgs. 2600 volt. 380/50

• Min working width (finished size): 25 mm • Max working width (finished size): 190 mm • Min. working height (finished size): 8 mm • Max working height (finished size): 115 mm • Min. workpiece length: 300 mm • Spindle speed: 6000 rpm • Spindle diameter: 35 mm • Min/Max tool diameter Horizontal spindles: 100 mm • Min. tool diameter of the vertical spindle right: 100 mm • Max tool diameter of the vertical spindle right: 100 mm • Min. tool diameter of the vertical spindle on the left: 100 mm • Max tool diameter of the vertical spindle on the left: 100 mm • Clamping length Vertical spindles: 110 mm • Clamping length Horizontal spindles: 180 mm • Diameter of feed rollers: 120 mm • Feed table length: 1800 mm • Quick adjustment task table and wing ruler: 10 mm • Diameter of the suction nozzle: 200 mm • mechanical indicators for width and h ...

Four-sided planing machine Harbs 250 x 150 mm 7 spindles 350 hours of uptime 3 m1 dressing table 8 newly rubberized feed rollers Grooved bed The machine is practically as good as new, ready for operation Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 fax 0041 62 966 21 12

Key data: 8 , 600 , 230

High-performance industrial planing machine In good condition, lots of accessories '

I sell the four-side planer Futura P-MAX 23/5+UNIV, built in 2008. 6 Spindle: bottom - right - left - top - bottom - universal Electronic programming for working width, working height and feed speed. Element max. 230x170mm ! All 6 spindles 6000 rpm. Material prints for short elements. Weight 2500kg. 1-zone pneumatic material pressure system for feed Fully operational. Available the same. Exhibition machine, has worked very little !

Part Number 6338 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 160mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 160mm 5,5kW 3) vertical left 160mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 7,5kW 6) horizontal bottom 230mm 7,5kW 7) universal 360° 230mm 7,5kW - all spindles adjustable up/down, right/left - spindle diameter 40mm - all spindles equipped with a brake - spindle speed 6000rpm in advance: - 6 pulling, toothed, metal introductory shafts, including 2 double - 4 pulling shafts, rubber including 1 double - 3 clamps on the lead bottom: - pressure from the side on the inlet - introductory shaft, toothed, pulling, swivel in the lower table top - 3 pull rollers, metal, smooth - pneumatically adjustable shafts - length of the introductory table top 1190mm - central lubricati ...

Part Number 6368 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 130mm 7 spindles: 1) horizontal bottom 230mm 5,5kW 2) vertical right 130mm 5,5kW 3) vertical left 130mm 5.5kW 4) horizontal top 230mm 7,5kW 5) horizontal upper 230mm 11kW 6) horizontal bottom 230mm 18,5kW 7) universal 230mm adjustable at 360 degrees 5.5kW - all spindles adjustable up/down, right/left - all spindles equipped with an electric brake - spindle diameter 40mm - spindles 4 and 5 electrically adjustable up/down - from above 8 metal pulling introductory shafts, swivel including 2 double - from above 4 pulling rollers, rubber - pressure from above 2pcs - from the bottom of the ratchet - from the bottom from the side 3 clamps - from below 2 metal rollers, smooth, pulling - from the bottom 2 double rollers, pulling, rubber - pneumatically pressed shafts ...

Part Number 6393 TECHNICAL DATA - max width of the workpiece 200mm - max height of the workpiece 150mm - number of spindles 4: 1) horizontal bottom 200mm 5,5kW 2) vertical right 150mm 4kW 3) vertical left 150mm 4kW 4) horizontal upper 200mm 5,5kW - all heads adjustable up/down, right left - spindle diameter 40mm - spindle speed 6000rpm in advance: - pulling introductory shafts, toothed 6 pcs including 2 double - 1 pulling shaft, rubber bottom: - introductory shaft toothed, pulling, torsional in the lower table top - side pressure 3pcs - lead roller, pulling, metal, smooth - all pneumatically pressed rollers - length of the introductory table top 2130mm - table top adjustable up / down - central lubrication - electrical setting of planing thickness - lifting motor 1,1kW - smooth regulation of the feed speed on the inverter - feed motor 3kW - feed  ...

I sell the moulding heads for the automatic fourside moulder WACO Weinig Gruppe. Inside diameter 50mm Outside diameter (with knives) 170mm Body diameter 155mm 15 pcs. working length 200mm (without knives). 8 pcs. working length150mm (with knives) Each with Hydro holding. Price per pc. 500 euros. Sellable per pc. or totally together. Available immediately.

Heavy high-performance planer designed for maximum feed performance and productivity. Designed for rough use in planing and sawmills. Suitable for the processing of planed goods and slats. Special features: Left version. for wood widths up to 360 mm. Machine we sell as used. But the machine never ran. Electrical part still has to be built by Ledinek - here adjustments are possible (axe positioning, FU-s, 400V or 480V etc.). Price is for the variant in the PDF description. Adjustments on request. Drive motors available.

ORDER NO. 6575 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 170mm - 7 spindles: 1) horizontal bottom 230mm, 11kW 2) vertical right 170mm 3) vertical left 170mm (2 and 3 spindle), 11kW 4) horizontal right 170mm, 5.5kW 5) horizontal upper 230mm, 11kW 6) horizontal bottom 230mm, 7.5kW 7) universal 230mm, adjustable at 360°, 7.5kW - all spindles adjustable up/down, right/left - spindle 3 and 5 electrically adjustable - ATS - spindle diameter 40mm - electric brakes - from above 4 pulling introductory shafts, toothed including 1 double - from above the introductory roller pulling rubber double - from above the shaft leading out, pulling, rubber, double - from below 2 metal rollers, pulling, smooth - pulling roller, rubber, double - feed on cardan rollers - pneumatically pressed shafts - smooth adjustment of the feed spe ...

CATALOG NUMBER 6679 TECHNICAL DATA - max width of the workpiece 250mm - max height of the workpiece 170mm 6 spindles: 1) horizontal lower 250mm 5.5kW 2) vertical right 170mm 5.5kW 3) vertical left 170mm 5.5kW 4) horizontal, upper 250mm 7.5kW 5) horizontal lower 250mm 7.5kW 6) universal 250mm, adjustable at an angle of 360 ° 5.5kW - 6 electrically adjustable spindle up / down - all adjustable spindles up / down, right / left - diameter of the spindles 40mm - 6 introductory pulling rollers, toothed, including 2 double ones - 6 rollers leading out, pulling, rubber, smooth, including 2 double - 2 clamps from above - from the bottom, a roller introducing toothed, pulling, torsion in the table before the first spindle - at the bottom, 2 pulling rollers, metal, smooth - 4 side clamps at the bottom - feed on cardan shafts - pneumatically pressed rollers - smooth regulati ...

CATALOG NUMBER 6674 TECHNICAL DATA - max planing width 150mm - max planing height 130mm 7 spindles: 1) horizontal lower 150mm 3kW 2) vertical right 130mm 3kW 3) vertical left 130mm 4kW 4) horizontal upper 150mm 4kW 5) horizontal lower 150mm 3kW 6) vertical right 130mm 4kW - diameter of all spindles 35mm - all adjustable spindles up / down and right / left - from above, 4 pulling rollers, toothed - 4 rubber, pulling rollers from above - 2 clamps from above - electric adjustment of the planing thickness of 0.25kW - length of the introductory top 1970mm - central lubrication of the table top - smooth regulation of the feed speed - 1.5kW feed motor - diameters of the extraction ports 6x120mm - dimensions length / width / height 4000x1300x1600mm - weight about 3000 kg - German production - for 6 heads - used planer, very good condition Net price: PLN 36900  ...

CATALOG NUMBER 6651 TECHNICAL DATA - max width of the workpiece 220mm - max height of the workpiece 120mm - 4 spindles: 1) horizontal bottom 220mm 4kW 2) vertical right 120mm 4kW 3) vertical left 120mm 4kW 4) horizontal upper 220mm 5.5kW - all adjustable spindles up / down, right / left - diameter of the spindles 40mm - from above, 4 introducing rollers, toothed, including 2 double ones - from above, 1 pulling roller, smooth, rubber - rubber, pulling roller at the bottom - pneumatically pressed rollers - feed on cardan shafts - 1.1kW feed motor - 0.37kW lifting motor - electric adjustment of the planing thickness - length of the introductory top 1980mm - side pressure - smooth adjustment of the feed speed 8-16m / min - central lubrication - diameter of the extraction port 5x140mm - locked in the cabin - dimensions length / width / height 3400x1500x1700mm - wei ...

Catalog No. 6765 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 160mm number of spindles 4: 1) horizontal bottom 230mm 5.5kW 2) vertical right 160mm 5.5kW 3) vertical left 160mm - electrically adjustable right/left from the control panel 5.5kW 4) horizontal top 230mm - electrically adjustable up/down from the control panel 7.5kW - all spindles adjustable up / down, right left - spindle diameter 40mm in advance: - introductory pulling rollers, toothed 6 pcs, including 2 double - pulling out rollers, rubber 2 pcs from down: - introductory toothed, metal, torsion roller in the bottom plate + - smooth metal pulling roller - pneumatically adjustable rollers - length of the introductory tabletop (with pneumatic feeder) 3390mm - the ability to work without switching on the pneumatic feeder, - adjustable top / bottom - central lubrication - ...