Hydraulic presses used for sale (23)

Bending press ITALPRESSE mod. PHF 60 - CE rules - Platens dim. mm. 1600X1100 - N. 4 cylinders - Max opening 1000 - Motors max 1.5 kw - Volt. 380/50 - Year 2001

Technical data Machine Type: Press Manufacturer: TOX PRESSOTECHNIK GmbH & Co. KG Press Type: MAG 030.226.A.001 Serial Number: 315604 Drive: TOX Powerhouse S 30.113.140.12D-LF Pneumatic connection: G 3/4\" Electrical connection: 230 VAC Maximum pressing force: 170 kN (6 bar), 300 kN (10 bar) Minimum air pressure: 3 bar Maximum air pressure: 10 bar Stroke: 140 mm (total), 12 mm (power stroke) Ambient temperature: 10°C to 60°C Weight: approx. 1150 kg Year of Make: 2007 Configuration Control: STE 325-130-3/4 Compressed air: filtered and dried (max. 40 μm) Note: Powerhouse should be renewed Auction-ID: A1-45711-324

PART NUMBER: 7553 Specifications: - dimensions of the hobs 2550x1100mm - number of batches 1 - electrically heated shelf - ground clearance 360mm - Number of cylinders 4 - cylinder diameter 80mm - emergency disconnection of the machine - total power 15.5kW - 1.5kW pump motor - dimensions length/width/height 2900x1300x2100mm - weight about 3000kg ADVANTAGES – made in Germany – electrically heated shelves – golden shelves – unpainted – very good condition – used press Net price: 27900 PLN Net price: 6488 EUR depending on the price 4.30 EUR (Prices may change with higher fluctuations)

Defects: air leakage (upper frame); incomplete cycle; oil leakage on hydraulic cylinders; machine not operated for ~6 years; further faults possible; sold for repair/parts Auction-ID: A7-40551-25

PART NUMBER: 7552 Specifications: - dimensions of the hobs 2550x1350mm - number of batches 2 - electrically heated shelf - total ground clearance 400mm - Clearance between shelves 280mm and 100mm - Number of cylinders 4 - cylinder diameter 90mm - 1.1kW pump motor - total power 31.3kW - dimensions length/width/height 3050x1600x2200mm - weight about 3500kg ADVANTAGES – made in Germany – electrically heated shelves – unpainted – very good condition – used press Net price: 28900 PLN Net price: 6721 EUR depending on the price of 4.30 EUR (Prices may change with higher fluctuations)

pressure: 7 tthroat: 180 mmstroke: 100 mmtable surface area: 320x300 mmram surface: Ø110 mmhole in the table: Ø50 mmtable height: 850 mmtool hole in ram: Ø30 mmweight of the machine ca.: 1,5 tdimensions of the machine ca.: BxTxH 1300x1300x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

HOT PRESS model OMC PL 90 , with diathermic oil heating second hand machine machine worked very very little excellent working conditions , like new CE compliant machine diathermic oil heating via built-in electric boiler heating power KW 9 / 18 for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.85 max. thrust Ton.90 opening mm.400 hydraulic pump motor power Hp 3 n.4 racks for table lifting guide max. thrust 2.5 kg/cm2 total installed power 21 kW volt. 380/50 net weight kgs. 4500

pressure: 30 tdistance between columns: 1200 mmstroke: 500 mmtable surface area: 1200x1000 mmram surface: 600x400 mmtable height: 850 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 4 tdimensions of the machine ca.: BxTxH 2400x2200x3400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

JJZ-CP type press designed for the production of plywood, doors, MDF. The glued elements are fed and removed from the press automatically by means of driven rollers. The press can be used with glue feeders. Specifications: -max. pressure 500T/ adjustable/ -max. load height 1300mm -max. batch size 1300x2500 -press size 3600x1370x4500 mm -press foundation ~500 mm below the floor level -feeding table 2000x1960 mm -receiving table 2350x2500 mm -max. power 13.2 kW -Ce -capacity of 6 batches per hour Currently, we glue panel doors and MDF board on presses. Very good technical condition. We offer a plywood production line dedicated to these presses.

pressure: 250 tdistance between columns: 600 mmstroke: - mmtotal power requirement: 22 kWweight of the machine ca.: 9 tdimensions of the machine ca.: 2 x 2 x 3,2 mNo. 3421Mould press 2500 / 700 kNSingle stroke 2-handSingle stroke foot switchAutomatic continuous run set-up and tippingTable 500 x 500Working range: Pressure capacity 250 tonnesDrive: ^22The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SPECIFICATIONS: Cold press Working table mm: 2500 x 1300 No. 4 pistons Vertical stroke: 450 mm

pressure: 200 ttable surface area: 2100 x 1400 mmpassage width: 2122 mmtotal power requirement: 60 kWweight of the machine ca.: 35 tdimensions of the machine ca.: mPress/punch with injection molding unit200 ton punch upstroke press with injection molding machine (400to)Additional guard locking via 4 power strokesManufacturer: R+S TechnikYear of construction: 2013 / rebuild 2016Mains voltage/frequency: 400V/50Hz 3~(N/PEConnected load: 60KWWeight about 35000kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Embossing press - embossing machine Hydraulic Pressing surface, 600 x 2700mm Heated pressing surface

pressure: 7 tthroat: 180 mmstroke: 100 mmtable surface area: 300x300 mmram surface: Ø105 mmhole in the table: Ø60 mmtable height: 1050 mmtool hole in ram: Ø30 mmtotal power requirement: kWdimensions of the machine ca.: BxTxH 1200x1200x2100 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 3000 x 1600 Number of pistons: 2 diameters Ø 200 mm Piston stroke mm: 1400 -Fence -Oil pump - 02 Steam outlet openings

pressure: 20 tdistance between columns: 450 mmstroke: 100 mmtable surface area: 440x320 mmram surface: Ø140 mmhole in the table: Ø50 mmtable height: 900 mmtool hole in ram: Ø40 mmtotal power requirement: 3 kWweight of the machine ca.: 2 tdimensions of the machine ca.: BxTxH 1400x1200x2200 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic press Pellegrini Hot water Pressing area 4000 mm x 1300 mm manual glue application incl. Insertion table Acceptance: Vacuum - Gantry forklift SIRIO

pressure: 25 tdistance between columns: 800 mmstroke: 100 mmdayligth: 450 mmtable surface area: 750x750 mmweight of the machine ca.: 3 tdimensions of the machine ca.: 1500x1500x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 1100 mmstroke: 400 mmdayligth: 600 mmtable surface area: 1000x800 mmram surface: 1000x800 mmtable height: 950 mmtotal power requirement: 65 kWweight of the machine ca.: 25 tdimensions of the machine ca.: BxTxH 0000x0000x3900mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tthroat: 275 mmstroke: 150 mmtable surface area: 860x550 mmram surface: 600x400 mmtable height: 810 mmtool hole in ram: Ø 50 mmdayligth: max. 475 mmweight of the machine ca.: 7 tdimensions of the machine ca.: BxTxH 2000x2500x3300 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tdistance between columns: 625 mmstroke: 150 mmtable surface area: 580x450 mmram surface: 580x340 mmhole in the table: Ø 150 mmtable height: 850 mmtool hole in ram: Ø 45 mmcolumn travel -side: 200x200 mmweight of the machine ca.: ca. 6,0 tdimensions of the machine ca.: BxTxH ca. 1300x1300x2750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 900 mmstroke: 300 mmtable surface area: 850x900 mmram surface: 800x880 mmstroke: 300 mmtable height: 1050 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 400 tstroke: 300 mmtable surface area: 1200 x 700 mmram surface: 1200 x 700 mmdayligth: 500 mmadjustment of stroke: 300 mmreturn capacity: 348 kNcapacity of ejector: 100 kNejector stroke: 100 mmtotal power requirement: 65 kWweight of the machine ca.: 28 tdimensions of machine L x W x H: 4,4 x 2,75 x 4,0 m= Frame pressAccessories: tool changing table- next safety inspection according to stamp 05/2021 -- with cutting shock absorption damping force 4000 kN damping stroke 5 mm spindle adjustment 200 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.