troester rubber machines used for sale

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

90s cold feed extruder, GE 90 x 16 D Vac, make Troester, with large hose / profile spray head, drive 52 KW Siemens AC, 4 TCU Siengle

cold feed extruder - 60 mm x 18 D vacuum, with feed roller, drive 22 KW, screw speed 10 to 60 rpm, with gear pump, 5 TCU,

cold feed vacuum extruder Troester 90 mm x 18 D, with feed roller, drive 46 kW, pie speed 10 to 60 rpm, 5 TCU,

screw ø:: 90 mm screw length:: 16D screw speedl:: ca. 40 U/min drive power:: 48,5 kW Condition: used, overhauled to order, including warranty, including CE marking Specification: extruder – used with feed roller - Screw diameter: 90 mm - Screw length: L = 12D - Screw speed approx.: 40 rpm - Motor rated power: 48.5 kW - Belt drive, number of belts: 5 - Number of heating/cooling zones: 4 - Voltage: 3x 380V, 50Hz, N For further details, please refer to the attachment. Price on request, depending on design and customer requirements The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

roll surface width: 450 mm roll diam. toproll: 203 mm roll diam. bottom roll: 203 mm output: 8,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tyre testing machine - static balancer for passenger tyres. Tyre size from 15 "to 18" (20") CE certified More details see the attached description!

Mesh belt for AUMA / Rotocure new and unused Length: 14100mm Width: 2250mm

Berstorff Rotocure AUMA 20-S Drum dia: 2000mm Drum width: 2600mm Sandvic Steelbelt Description attached!

machine measurements: 1500 x 2400 x 1150 mm machine weight: -- kg power capacity: 12 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 3.000 mm machine weight: -- kg power capacity: 90 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.:  ...

Fogg & Young Bale Cutter

cross-section width:: 700 mm cross-section heigth:: 500 mm feed:: -- mm Condition: used, overhauled Specification: splitter for rubber bales - overhauled with CE - cross section width max.ca.: 700 mm - cross section height max. approx.: 500 mm - cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz - Infeed roller conveyor for product transport - Machine stands on a raised pedestal - Two-hand safety control for driving the blade movement - Safety guard according to current standards - New control cabinet - New on-board system machine - Operating and maintenance manual in English - CE marking - Paintwork: according to customer requirements - Refurbished with 1 year warranty - CE marking, Option: - Output roller conveyor new The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press (n°1) Upstroking Manufacturer: Agila Closing force: 850 Ton Year 1997 hydraulic Steam Platens : 3 2 cavities (250 mm opening) Size heating platens: 1100 x 1400 x 76 mm Diam. piston 650 mm Hydraulic pressure: max. 250 BAR Hydraulic tank: 500 L Complete manual included Size press 2400 x 1400 x 4200 mm (LWH) Weight +/- 23.000 kg

REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750

Refer to code 1049 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Z-Splicing Machine Make: Z-AUTOMATION Model: Z splicing stand alone Year 2014 8 kW, 6 bar Profile Cross sections 50 x 40 mm 2 - 4 splicing cavities Length 4600 mm Siemens Simatic HMI touch screen control Foot pedal control Emergency kill switch

Merkle Slitter 500mm wide

USI Cumberland Grinder / Granulator 28x20 50 Hp 8mm Grid 2 new dead blades 3 sharpened fly blades One new start / stop control box

cross-section width:: 40 (45) mm cross-section heigth:: 25 mm feed:: 1 - 999.999,9 mm speed of feed:: 1 - 60 m/min cuts max.:: 100 Schnitte/m Condition: used, Specification: circular knife cutting machine - second-hand for cutting rings, discs and profiles - diameter max.: 45 mm - 3 hoses or strands: 6 - 20 mm - 2 hoses or strands: 20 - 30 mm - 1 hose or string: 30 - 45 mm - cross section width max.: 40 mm - cross-section height max.: 25 mm - feed speed: 1 - 60 m/min, infinitely variable - Cutting capacity max.: 100 cuts/min depending on material and cutting length - Cutting length: 1 - 999.999,9 mm - Step jump: 0.1 mm - Feed by servo drive - Cutting by servo drive - Pulsed feed - Connected load approx.: 5 kW - Operating voltage: 3 x 400V, 50Hz, PE - Weight approx.: 550 kg - Dimensions (L/W/H): 1,940 x 890 x 175 ...

cross-section width:: 800 mm cross-section heigth:: 15 mm feed:: ab ca. 5 mm speed of feed:: m/min cuts max.:: Schnitte/m condition: used, overhauled Specification: Panel cutting machine - overhauled with CE - Section width max.approx.: 800 mm - Section height max.: 15 mm, depending on the hardness of the rubber sheets - Cutting length from approx.: 5 mm (depending on material) - cutting force approx.: 10 tons - Connected load approx.: 1.8 kW - Painting: green - Operating voltage: 3 x 400V, 50Hz, N, PE - Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards, - New on-board system machine, - New control cabinet with PLC system Siemens S7-1200, - CE marking, - Instructions for use and maintenance in English or German language The data for this ad was created with ModulMWS - the s ...

Press force max.:: 1.000 kN heating plates:: 480 x 520 mm electrically heated:: °C piston stroke:: ca. 500 mm no. of stages:: 1 Condition: Used, overhauled Specification: 4-column vulcanising press 480 x 520 mm, used - closing force: 100 t - closing: from top to bottom - heating plates: 2 electric plates - New heating platens - Dimensions of heating plates: 480 x 520 mm - Distance between heating platens approx.: 500 mm - AC motor: 5,5 kW - New electric valves - New control cabinet with Siemens 7 touch panel - SPS system Siemens S7-1200 - Frequency converter make Schneider - New cabling - Light curtains in the front operating area Overhauled according to CE standard safety regulations Operating and maintenance instructions in German Warranty: 1 year The data for this ad was created with ModulMWS - the software solution of LogoTech oH ...

cross-section width:: Schläuche max. 11 mm cross-section heigth:: 11 mm feed:: 0,5 - 100.000 mm Condition: used, very good condition Specification: universal cutting machine with roller drive for hoses - small cutting machine for hoses - feed unit: roller drive - microcontroller control: 80537 - cutting unit: pneumatic - Type of cut: Blade cut - Industrial blade: for PVC hoses - Max. hose diameter: 11 mm - Maintenance unit: yes - Max. feed speed: 1 - 50 m/min - Cutting capacity max.: 450 cuts/min depending on the cutting length - Cutting force approx.: 500 N at 6 bar - Cutting length: 0.5 - 100,000 mm - Resolution/step change: 0.5 mm - Operating voltage: 230V, 50-60 Hz - Compressed air: 5 - 6 bar - Air consumption per stroke approx.: 0.2 l/stroke at 6 bar - Paint finish: RAL 7035 light grey - No docum ...

Barwell Cryogenic Deflashing and Deburring Machine Freeze Trim Chamber Model BFT10

Merkle Slitter Cutting width 1m Overall dims: 1.4m wide x 700mm deep x 1m high Weight: 500kgs

Merkle 500mm wide Slitter

speed of feed:: 50 m/min feed:: 5 - 99.999,9 mm cuts max.:: 70 - 80 Schnitte/m cross-section width:: 40 mm cross-section heigth:: 40 mm Condition: NEW, Specification: Hose and corrugated pipe cutting machine electric cutting machine - Cutting unit: Window cut with cutting bushes - Material diameter approx.: 4 - 40 mm - Transport by two drive belts - Max. distance between the belts: 45 mm - Belt adjustment via motor, adjustment via control panel - Belt adjustment via the centre - with a maximum speed of approx.: 50 m/min - Electrical contact pressure of the drive belts - Electronic length measurement from 5 - 99,999.9 mm Digital display - Step change: 0.1 mm - Cutting via electric motor - Quantity selectable: 1 to 99,999 Display digital - Cutting capacity approx.: 70 - 80 pieces/min at 100 mm l ...

Press force max.:: 1600 kN heating plates:: 400 x 400 mm electrically heated:: -- °C heating power:: 9,92 kW piston stroke:: 400 mm no. of stages:: 1 Condition: Used, Specification: Press 400 x 400 mm, second-hand steel frame construction - Clamping force: 160 tonnes - pressure force: 1600 kN - Operating pressure: 300 bar - Closing: from bottom to top - Heating platens: 2 electric platens - Heating power: 4.96 kW/platen - Heating platen dimensions: 400 x 400 mm - Specific pressing pressure: 1000 N/cm² - Distance between the heating platens: 500 mm - Piston stroke: 400 mm - Piston diameter: 260 mm - AC motor power: 7.5 kW - Pneumatic protective cover in the front area, - lifting device - Sliding table - Approx. dimensions: 1,760 x 1,150 mm - System height approx.: 2,470 mm - Weight approx.: kg The data for this ad was cr ...

Merkle Metzner Profile Automatic Cutting Machine Model XCL Material direction right to left Type of cut: Die cut/scissor cut Year 2002 Belt feed Width of belt 100mm Contact belt 200/400mm Poly-v belts Material acceptance: max. 100x30mm Drive Stepping motor, 3 phases Max. feed rate 40m/min Max. torque 420 Ncm Connection values Voltage 230V Pressure: 6 bar

John Marshall Cutter

Autogil Cutter

MDR 2000 Rheometer Manuf.: Alpha Model 81001 220V 5amps Power 1000 VA Air pressure required PSI 120 max. / 70 min.

Press force max.:: 3000 kN heating plates:: 600 x 630 mm electrically heated:: °C heating power:: kW piston stroke:: 420 mm no. of stages:: 1 Condition: Used, reconditioned Specification: Press 600 x 630 mm, second-hand - clamping force: 300 tonnes (3,000 kN) - closing: from bottom to top - Heating platens: 2 electric platens, with new heating rods - Heating platen dimensions approx.: 600 x 630 mm - Distance between the heating platens approx.: 420 mm - New electric valves - AC machine output oil pump: 5.5 kW - New control cabinet with Siemens 7’ touch panel - PLC control system make Siemens S7-1200 - New cabling - Frequency inverter made by Schneider - Light barriers in the front area, Overhauled in accordance with CE standard safety regulations Operating instructions and maintenance instructions in German Warranty: 1 year The data for this ad was created with ModulMWS ...

New Zig-Zag Cutter! Machine is designed to cut an 800mm Batch into an endless strip for Extruder feeding. 12 month Warranty! Description attached!

machine measurements: 2.100 x 2.200 x 2.100 mm machine weight: 2.000 kg power capacity: 36 kW Condition: used Specification: cleaning and degreasing system FIRBIMATIC LOGICA 200V closed cleaning system for the cleaning of of metallic components with highly stabilised perchloroethylene - second-hand - Closed cleaning system for the cleaning of metallic components components with highly stabilised perchloroethylene. - PER-based cleaning and degreasing system Possible cleaning cycles: 1. pre-cleaning (spraying) 2. main cleaning (spray and flood cleaning) 3. rinsing (hosing down) 4. vapour degreasing 5. vacuum drying - All cleaning cycles are freely programmable. - Filling volumes: Tank 1: 170 litres Tank 2: 80 litres - Type of solvent: Perchloroethylene - Total connected load of motors: 9.65 kW - Installed electrical power incl. heating syst ...

Key data: 2000 mm, 1300 mm

available Berstorff Bias Cutter Angle 0-50 degrees with manual splice 90 degree with automatic splice Ce certified Description attached!

volt: 380 V weight: 1,4 t : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cevenini Log Cutter Model M200 1.5m wide x 200 mm diam. Complete with motor

machine measurements: ca. 1030 x 1110 x 1950 mm machine weight: 800 kg power capacity: ca. 2,8 kW Condition: used Specification: SiloStar 924 dosing system - used - For dosing liquid silicone LSR - LSR dosing with servo-hydraulic unit, servo motor 2.8 kW - Dosing with piston pumps - Uniform emptying of components A + B via proportional compensation cylinders - Variable mixing ratio - Touchscreen with visualised user interface - Containers: 200 litre drums - Operation via 10 inch touch display - Automatic mixing material pressure control with sensor directly on the mixing block - Pressure sensor for A + B - Circulation device A + B - Power connection: 380-480 VAC, 50/60 Hz (3P + PE), 16 A - Mixing head machine connection - Hose package 2x nylon DN 16 x 2500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Blackfriars Rotary Cutter / Granulator Model 12 ASHD/267 With sound booth

UNTHA Shredder Model RS30 Year 10/2023 Hours: 97 Power 22kW 400V/50Hz CE marked In ‘as new’ condition

Press force max.:: 1.000 kN heating plates:: 480 x 520 mm electrically heated:: 210 - 220 °C piston stroke:: ca. 400 mm no. of stages:: 1 Condition: Used, reconditioned Specification: 4-column vulcanising press 480 x 520 mm, used - Clamping force: 100 t - Closing action: bottom-up - Heating plates: 2 electric plates - Two new heating elements - Plate heating temperature: up to approx. 210–220 °C - Heating plate dimensions: 480 x 520 mm - Distance between heating plates approx.: 400 mm (to be determined during refurbishment) - Working height of lower plate: approx. 1,100 mm - AC motor: 5.5 kW (to be determined during refurbishment) - New solenoid valves - New control cabinet with Siemens 7 touch panel Type KTP700 Basic - Siemens S7-1200 PLC system - Schneider frequency converter - One remote maintenance unit - New cabling - Light cur ...

Key data: 3000 kN, 762 mm, 200 °C

Condition: Factory Rebuilt Model: 3000kN BIPEL Press Application: Compression Moulding Mode of Operation: Manual and Semi-Auto Frame structure: Steel plate frame Cylinder type : Double acting Push back cylinder(s) : Pressing force kN: 3000 Pull back force at circuit pressure kN: 300 Operating height mm : 820 Stroke mm : 610 Daylight between Tables mm : 1205 Table size L -R mm : 785 F-B mm : 890 Opening speed mm/sec: 200 Pressing speed mm/sec:  ...

Key data: 3000 kN

Bed Size: Left to Right 785mm 30 1⁄2 in Front to Back 890mm 35 in Daylight Between Tables 1206mm 47 1⁄2 in Daylight Between Heated Platens 841mm 33 1⁄8 in Heated Platen Sizes(Up To) 760mm x 610mm 28″x24″ Max Working Platen Temperature 220°C 428F Main Ram Stroke(Up To) 610mm 24 in Hydraulic Circuit Pressure 210 Bar 3000 PSI Main Ram Pressing Force 305 T 300 Ton Maximum Pummel Diameter 102mm 4 in Closing Speed(Up To) 150mm/s Opening Speed(Up To) 120mm/s

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

1 x Alpha Technologies Mooney MV2000e Viscometer software discs and operation manual are included. You will have to register the software. PC not available. In good condition.

1 x Farrel Bridge Model BR lab banbury mixer, Serial no. 91M7000, year: April 1991, Chamber volume 1.5litre pneumatic hopper and swing side discharge door, David Brown gearbox, 30kW DC variable speed motor and controls. Fully guarded with Key interlock system. Complete and in excellent condition.

Make: Engel Type: Vertical Rubber Injection Model: ES 280V/40VT-ELAST Serial number: 41938, Year of manufacture: 2000 Clamping force 400kN Injection volume 280cm3 Platen size: 860x400mm In good condition.

Knife Drawing No. 05714-223C1

Guided from bronze Drawing No. 05714 -227D1

Key data: 70

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

clamping force: 450 kN injection volume: 135 cm³ screw diameter: 35 mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPE - used clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 120 mm screw length:: 17D screw speedl:: 42 U/min drive power:: 138 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 90 mm screw length:: 20D screw speedl:: 0 - 60 U/min Condition: NEW, Specification: Rubber vacuum extruder - with warranty - Screw diameter: 90 mm - Screw length: L = 20 D (approx. 1,800 mm conveying length) - Screw speed: 0 - 60 rpm - Centre height of extruder: approx. 1,125 mm incl. base frame - Max. permissible injection pressure: 500 bar - with feed roller - Extruder water-tempered - Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump - Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm - Vacuum cylinder: three tempering zones BL = 1,057 mm - End cylinder: one temperature control zone approx. 4D = 360 mm - Number of tempering zones: 5 - Heating capaci ...

clamping force: 1.300 kN injection volume: 230 cm³ screw diameter: 45 mm platen size: 685 x 685 mm Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,3 ...

clamping force: 350 kN injection volume: 59 cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power ...

A rotational shear viscometer according to Mooney for performing Viscosity tests (ML / MS 1+X), Stress Relaxation testing, Mooney Scorch, Delta Mooney testing on polymers as well as rubber compounds for quality control, research and development applications.

Machine number 185386/2008

Machine number 205557/2012 Without softwear! Head failure!

Sample marker S1

LWB Steinl Injection Moulding / Vulcanizing Press Model: VCE-B Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 75 kW Hydraulic oil 40/45 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 1 Tool Kemp model TT-188 (year 2019) hot runner. Weight 12850 kgs

Maplan Injection Moulding Machine Model: MTF400/80C 80 Ton Safety distance 162mm Run-on time 81ms Follow-up 5mm Pattern size 510mm x 410mm Touch screen control Year 2010

LWB Steinl Injection Moulding / Vulcanizing Presses Models available: VCEFE-B and VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Weight 13500 kgs

LWB Steinl Injection Moulding / Vulcanizing Press Model: VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Year 2013 Weight 13500 kgs

Rheometer Make: Alpha Technologies Model MDR 2000 P

Monsanto ODR 2000 E Rheometer With manual

Mooney Viscometer Make: Alpha Technologies Model MV 2000 Rotational Speed 0.1 to 10 rpm, temperature Range ambient to 200C, torque Range 0.01 to 200 MU, rotors large: 38.10 mm D, small: 30.48 mm D.

Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993

Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009

Yizumi Injection Press Model: YL2-V280L Clamping force 2800 kN Volume: 2000cc Mold open stroke 500mm Min. mold height 100mm Heated platen size 670mm x 780mm Heating plate daylight 600mm Injection pressure 1970 bar Theoretical Injection volume 2000cm3 Oil pump power 11kW System pressure 230 bar Total power 37kW Power supply: 415V, 50Hz, 3P+N+PE Rexroth variable pump + Inovance servo motor: Year 2021 CE marked

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

LWB Steinl Injection Machine Type VREFE 1600/1000/170 Heating platen size 500 X 510 X 63 mm Sliding platens Top and bottom ejectors Clamping force 1600kN Opening force clamp 100kN Clamping stroke 395mm Injection volume E 1000 ccm Max. Injection Pressure E 2200 bar Injection volume EF 170 ccm Max. Injection Pressure EF 1800 bar Hours: 700 since new Year 2009 Weight 6000kg

LWB Steinl Injection Machine Type VCE -T 500/160 T Clamp power 500 KN Injection volume 160 cm3 Year 2006 6 Bar 400 v 50 hz 26 KW