Four-sided planing machines LEDINEK EUROPLAN 600 4V+4F-S60

Number of spindles: 4 Working width: 600 mm Working height: 300 mm FINAL PLANING LINE FOR STRAIGHT GLULAM PRODUCED BY LEDINEK => EUROPLAN 600-4V+4F S60 WITH INFEED AND OUTFEED MECHANIZATION
Orientation: right machine

This four-sided heavy-duty planer for timber was specially designed for planing of constructional timber and glulam beams. The machine is suitable for green as well as kiln dried timber. Machine is equipped with hydro cutterheads.

The adjustment of cut off on the first cutterhead is motor driven. Set value is shown on operational panel.
One’s desired thickness is set through an adjustable top unit with second cutterhead, the adjustment is motor driven with spindle lift mechanism in 6 columns with 120 mm diameter. The set thickness is shown on operational panel.

The vertical units enable good clean surface or profiling. The machine has two opposite vertical floating heads (float up to 40 mm) so they can adjust to the curvature of the beams. The floatation of the left vertical unit is actuated by a pneumatic cylinder. The side pressure shoes can be adjusted according to the toll diameter.
Both vertical units can be axially adjusted for 20 mm. (under the working table level), digital display of position. The spindles are mounted with support bearings.

The adjustment of cut off on the right vertical cutterhead is motor driven. Set value is shown on operational panel.
Adjustments of the planing width is motor driven. Set value is shown on operational panel.
Essential adjustments can be carried out on the front side of the machine.

Four-sided milling units 2 + 2
The upper milling units are pneumatically actuated. Chamfer size is manually adjustable. The units are mounted just after the vertical spindles and are attached as vertically floating heads.
The lower chamfers are made with milling tools under the planing heads on the vertical spindles.
Tools: Milling heads with carbide turnover knives.

Feeding system with frequency converter allows infinitely variable feed speed, which can be set according to thickness and quality of workpiece.
The set value can be read off a display with scale.

A robust heavy duty feeding system:
Reliable feed is ensured with three synchronized driven roll pairs with big diameters.
First top feed roll with 240 mm diameter is helical toothed, hard chromed and pressurized with air bellows.
Second and third top feed rolls with 240 mm diameter are smooth and pressurized with air bellows.
First table feed roll with 190 mm diameter is helical toothed, hard chromed and pressurized with air bellows.
Second and third table feed rolls with 190 mm diameter and parallel lifting.
Pneumatically pressurized pressure beams before the second planing spindles, and adjustable pressure shoe behind.
Pneumatically pressurized side roll on the infeed table is adjustable by motorized drive.

TECHNICAL DATA
Working dimensions:
Planing width: 50 - 600 mm
Planing height with chamfering: 35 - 300 mm
Planing height without chamfering: 19 - 300 mm
Planing length: min. 1.900 mm
Table height: 1.000 mm
Feed speed: 12 10 - 60 m/min.

Drive motors
First spindle - bottom: (up to 30 kW possible) 22 kW
Second spindle - top: (up to 37 kW possible) 30 kW
Vertical spindle - left: (up to 22 kW possible) 18,5 kW
Vertical spindle - right: (up to 22 kW possible) 18,5 kW
Chamfering: 2 x 1,85 kW
Feeding: 6 x 3 kW

Working spindles:
Horizontal spindles rpm: 5.000 rpm
Vertical spindles rpm: 6.000 rpm
Spindle diameter: 50 mm
Tooling length of horizontal spindles: 630 mm
Tooling length of vertical spindles: 330 mm
Chamfer spindles rpm: 12.000 rpm
Chamfer spindles diameter: 20 mm

Tool diameters (cutting circles) on:
Horizontal spindles: 165 mm
Vertical spindles: 140 - 220 mm
Chamfers top: Ø 100 / 45° x 14 mm
Chamfers bottom: Ø 160 / 45° x 14 mm
seller offer No. resale 5060